vacuubrand VACUU-PURE 10C Instructions For Use Manual Download

Page: 32 / 96

20901224_EN_VACUU·PURE 10C_V1.8_221122

Installation and connection

4 Installation and connection

Installation and connection

4.1

4.1 Transport

Transport

Products from

VACUUBRAND

are packed in sturdy, recyclable

packaging.

The original packaging is accurately matched to your

product for safe transport.

If possible, please keep the original packaging, e.g., for

returning the product for repair.

Goods receipt

Check the shipment for transport damage and completeness.

Immediately report any transport damage in writing to the

supplier.

Unpacking

Power cord

Vacuum pump manual

Remove the upper part of the foam packaging.



Example

Vacuum pump in

original packaging

Summary of Contents for VACUU-PURE 10C

































































































Search results

Summary of Contents for VACUU-PURE 10C

Reviews:

Related manuals for VACUU-PURE 10C

Brands by name

Popular brands

vacuubrand VACUU-PURE 10C, Instructions For Use Manual

Search results

Summary of Contents for VACUU-PURE 10C

Reviews:

Related manuals for VACUU-PURE 10C

Brands by name

Popular brands