vacuubrand MD 12C NT VARIO o.C. Instructions For Use Manual Download Page 84

Page: 84 / 92

20901544_E12C+16C_NT Vsel_V1.2_260922

Appendix

Ordering information

for spare parts

Spare parts

Order no.

Anti‑rotation protection D17x17.5

20635113

Gas ballast cap

20639223

Service kit MD 12C / MV 10C NT VARIO select

20696839

Service kit ME 16C NT VARIO select, 2x

20696867

Power cable

CEE

20612058

20676021

20635997

IND

20635365

20612065

A full list of spare parts available can be found under



VACUUBRAND > Support > Instructions for repair >

Chemistry diaphragm pumps

Sources of supply

Purchase original accessories and original spare parts from a

subsidiary of

VACUUBRAND GMBH + CO KG

or your local dis

‑

tributor.

Information about our complete product range is available

in the current

product catalog

Your local distributor or

VACUUBRAND GMBH + CO KG

sales office

is available to assist you with orders, questions

on vacuum control and optimal accessories.

International

sales offices and

distribution

Summary of Contents for MD 12C NT VARIO o.C.





























































































Search results

Summary of Contents for MD 12C NT VARIO o.C.

Reviews:

Brands by name

Popular brands

vacuubrand MD 12C NT VARIO o.C., Instructions For Use Manual

Search results

Summary of Contents for MD 12C NT VARIO o.C.

Reviews:

Brands by name

Popular brands