Vacon 100 HVAC Applications Manual Download

Page: 53 / 201

PARAMETERS MENU

The HVAC Application has the following parameter groups:

Menu and Parameter group

Description

Group 3.1: Motor settings

Basic and advanced motor settings.

Group 3.2: Start/Stop setup

Start and stop functions.

Group 3.3: Control reference settings

Frequency reference setup.

Group 3.4: Ramp & Brakes Setup

Acceleration/Deceleration setup.

Group 3.5: I/O Configuration

I/O programming.

Group 3.6: Fieldbus Data Mapping

Fieldbus data out parameters.

Group 3.7: Prohibit Frequencies

Prohibit frequencies programming.

Group 3.8: Limit supervisions

Programmable limit controllers.

Group 3.9: Protections

Protections configuration.

Group 3.10: Automatic reset

Auto reset after fault configuration.

Group 3.11: Timer functions

Configuration of 3 timers based on Real Time Clock.

Group 3.12: PID-controller 1

Parameters for PID Controller 1. Motor control or

external usage.

Group 3.13: PID-controller 2

Parameters for PID Controller 2. External usage.

Group 3.14: Multi-pump

Parameters for multi-pump system.

Group 3.16: Fire mode

Parameters for Fire Mode.

Group 3.17 Application Settings

Group 3.18 kWh Pulse Output

Parameters to configure a digital output that gives

pulses that agree to the kWh counter.

5.1

GROUP 3.1: MOTOR SETTINGS

NOTE!

These parameters are locked if drive is in the run state.

PARAMETERS MENU

VACON · 53

24-HOUR S358 (0)201 212 575 · EMAIL: [email protected]

Summary of Contents for 100 HVAC










































































































































































































Search results

Summary of Contents for 100 HVAC

Reviews:

Related manuals for 100 HVAC

Brands by name

Popular brands

Vacon 100 HVAC, Applications Manual

Search results

Summary of Contents for 100 HVAC

Reviews:

Related manuals for 100 HVAC

Brands by name

Popular brands