Vacon 100 HVAC Applications Manual Download

Page: 35 / 201

3.2.5

COMPARING THE PARAMETERS

With this function, you can compare the current parameter set with 1 of these 4 sets.

•

Set 1 (P6.5.4 Save to Set 1)

•

Set 2 (P6.5.6 Save to Set 2)

•

The defaults (P6.5.1 Restore Factory Defaults)

•

The keypad set (P6.5.2 Save to Keypad)

See more about these parameters in Table 57 The parameter compare.

NOTE!

If you have not saved the parameter set with which you want to compare the

current set, the display shows the text Comparing failed.

USING THE FUNCTION PARAMETER COMPARE

Go into Parameter Compare in the User settings

menu.

STOP

READY

I/O

ID:

M6.6

User Settings

Language Selection

Parameter Backup

Parameter Compare

English

(4)

(7)

Make a selection of the pair of sets. Push OK to

accept the selection.

STOP

READY

I/O

ID:

B6.6.1

Parameter Compare

Active set-Set 1

Active set-Set 2

Active set-Defaults

Make a selection of Active and push OK.

STOP

READY

I/O

ID:

M6.6.1

Active set-Set 1

Active

Help

Add to Favourites

USER INTERFACES

VACON · 35

24-HOUR S358 (0)201 212 575 · EMAIL: [email protected]

Summary of Contents for 100 HVAC










































































































































































































Search results

Summary of Contents for 100 HVAC

Reviews:

Related manuals for 100 HVAC

Brands by name

Popular brands

Vacon 100 HVAC, Applications Manual

Search results

Summary of Contents for 100 HVAC

Reviews:

Related manuals for 100 HVAC

Brands by name

Popular brands