Vacon 100 HVAC Applications Manual Download

Page: 183 / 201

C. The number pumps that operate

increases or decreases, if the PID

controller cannot keep the process value

feedback in the specified bandwidth

around the setpoint.

D. The specified bandwidth around the

setpoint.

10.15

FIRE MODE

When Fire mode is active, the drive resets all faults that occur and continues to operate at

the same speed until it is not possible. The drive ignores all commands from the keypad,

fieldbuses, and the PC tool.

The Fire mode function has 2 modes, the Test mode and the Enabled mode. To make a

selection of a mode, write a password in parameter P3.16.1 (Fire Mode Password). In the

Test mode, the drive does not automatically reset the faults, and the drive stops when a fault

occurs.

NOTE!

This input is normally closed.

When you activate the Fire mode function, an alarm shows on the display.

CAUTION!

The warranty is void if the Fire mode function is activated! You can use Test mode

to test the Fire mode function and the warranty stays valid.

P3.16.1 FIRE MODE PASSWORD (ID 1599)

Use this parameter to enable the Fire Mode function.

NOTE!

All other Fire Mode parameters will be locked when the Fire Mode is enabled and

correct password is set in this parameter.

Selection

number

Selection name

Description

1001

Enabled mode

The drive resets all the faults and continues to operate at the

same speed until it is not possible

1234

Test mode

The drive does not automatically reset the faults, and the

drive stops when a fault occurs.

P3.16.2 FIRE MODE ACTIVATION ON OPEN (ID 1596)

Use this parameter to select the digital input signal that activates the Fire Mode function.

If this digital input signal is activated, an alarm shows on the display, and the warranty

becomes void. The type of this digital input signal is NC (normally closed).

PARAMETER DESCRIPTIONS

VACON · 183

24-HOUR S358 (0)201 212 575 · EMAIL: [email protected]

Summary of Contents for 100 HVAC










































































































































































































Search results

Summary of Contents for 100 HVAC

Reviews:

Related manuals for 100 HVAC

Brands by name

Popular brands

Vacon 100 HVAC, Applications Manual

Search results

Summary of Contents for 100 HVAC

Reviews:

Related manuals for 100 HVAC

Brands by name

Popular brands