manualshive.com logo in svg

Vacon 100 HVAC, Applications Manual

The Vacon 100 HVAC is a versatile and efficient product designed for heating, ventilation, and air conditioning systems. Enhance your understanding and optimize its usage with the comprehensive Applications Manual, available for free download from our website. Unlock its full potential today!

Share
Download
background image

P3.13.1.2 OUTPUT IN STOP (ID 1100)

Use this parameter to set the output value of the PID controller as a percentage of its

maximum output value when it is stopped from a digital output.

10.14

MULTI-PUMP FUNCTION

The Multi-pump function lets you control a maximum of 4 motors, pumps or fans with the

PID controller.

The AC drive is connected to a motor, which is the regulating motor. The regulating motor

connects and disconnects the other motors to/from the mains with relays. This is done to

keep the right setpoint. The Autochange function controls the sequence in which the motors

start to make sure that they wear equally. You can include the regulating motor in the

autochange and interlock logic, or set it to always be Motor 1. It is possible to remove motors

momentarily with the Interlock function, for example for maintenance.

ON
OFF
ON
OFF

Delay

Bandwidth

Feedback

Setpoint

Drive is running at maximum

or close to maximum frequency

M1

M2

Fig. 44: The Multipump function

If the PID controller cannot keep the feedback in the set bandwidth, a motor or motors are

connected or disconnected.

When to connect and/or add motors:

•

The feedback value is not in the bandwidth area.

•

The regulating motor operates at a close to maximum frequency (-2 Hz).

•

The conditions above are true for longer than the bandwidth delay.

•

There are more motors available

PARAMETER DESCRIPTIONS 

VACON · 175

24-HOUR S358 (0)201 212 575 · EMAIL: [email protected]

10 

Summary of Contents for 100 HVAC










































































































































































































Reviews:

No comments

Related manuals for 100 HVAC

Gantner E Series Communications Manual preview
E Series
Brand: Gantner Pages: 56
Bartlett Genesis LT3140 Technical Manual preview
Genesis LT3140
Brand: Bartlett Pages: 5
Hama Thunder V18 Instruction Manual preview
Thunder V18
Brand: Hama Pages: 12
Hama Thunder V18 Operating Instruction preview
Thunder V18
Brand: Hama Pages: 12
Hama Mini V3 Rumble Operating Instruction preview
Mini V3 Rumble
Brand: Hama Pages: 14
Hama Dual Vibration Operating Instruction preview
Dual Vibration
Brand: Hama Pages: 8
M-system SC100 Series Applications Manual preview
SC100 Series
Brand: M-system Pages: 103
M-system MSP40 Instruction Manual preview
MSP40
Brand: M-system Pages: 18
M-system 47LV Specifications preview
47LV
Brand: M-system Pages: 7
GBD BE24G Installation Instructions Manual preview
BE24G
Brand: GBD Pages: 60
Dantel 44093 Installation & Operation Manual preview
44093
Brand: Dantel Pages: 6
JCM GAMMA VERSUS Series Manual preview
GAMMA VERSUS Series
Brand: JCM Pages: 111
WAGO 767-4804/000-800 Manual preview
767-4804/000-800
Brand: WAGO Pages: 80
TEL AFA4000/1/AS Installation And Calibration Manual preview
AFA4000/1/AS
Brand: TEL Pages: 26
Vimar EAM6 Installation And Operation Manual preview
EAM6
Brand: Vimar Pages: 32
Baier 50VA Instruction Manual preview
50VA
Brand: Baier Pages: 20
Daikin RoCon BF Operating Instructions Manual preview
RoCon BF
Brand: Daikin Pages: 64
Qcells Q.PEAK DUO BLK ML-G10/t Series Installation And Operation Manual preview
Q.PEAK DUO BLK ML-G10/t Series
Brand: Qcells Pages: 13

Brands by name

Popular brands

Load more brands