manualshive.com logo in svg

Vacon 100 HVAC, Applications Manual

The Vacon 100 HVAC is a versatile and efficient product designed for heating, ventilation, and air conditioning systems. Enhance your understanding and optimize its usage with the comprehensive Applications Manual, available for free download from our website. Unlock its full potential today!

Share
Download
background image

To make a selection of a preset frequency between 1 and 7, give digital inputs to P3.5.1.15

(Preset Frequency Selection 0), P3.5.1.16 (Preset Frequency Selection 1), and/or P3.5.1.17

(Preset Frequency Selection 2). The different sets of active digital inputs determine the

preset frequency. You can find more data in the table below. The values of the preset

frequencies stay automatically between the minimum and maximum frequencies (P3.3.1 and

P3.3.2).

Necessary step

Activated frequency

Make a selection of the value 1 for parameter P3.3.3.

Preset frequency 0

Table 59: The selection of preset frequencies when P3.3.10 = Binary coded

Activated digital input signal

Activated frequency

reference

B2

B1

B0

Preset frequency 0

*

Preset frequency 1

*

Preset frequency 2

*

*

Preset frequency 3

*

Preset frequency 4

*

*

Preset frequency 5

*

*

Preset frequency 6

*

*

*

Preset frequency 7

* = the input is activated.

P3.3.19 PRESET ALARM FREQUENCY (ID 183)

Use this parameter to set the frequency of the drive when a fault is active and the response

to the fault is set to 'Alarm + Preset Frequency'.

10.3.3

MOTOR POTENTIOMETER PARAMETERS

P3.3.20 MOTOR POTENTIOMETER RAMP TIME (ID 331)

Use this parameter to set the rate of change in the motor potentiometer reference when it is

increased or decreased.

The parameter value is entered as Hz/second.

P3.3.21 MOTOR POTENTIOMETER RESET (ID 367)

Use this parameter to set the logic for the resetting of the frequency reference of the motor

potentiometer.

PARAMETER DESCRIPTIONS 

VACON · 127

24-HOUR S358 (0)201 212 575 · EMAIL: [email protected]

10 

Summary of Contents for 100 HVAC










































































































































































































Reviews:

No comments

Related manuals for 100 HVAC

ABB FDNA-01 Quick Installation And Start-Up Manual preview
FDNA-01
Brand: ABB Pages: 2
Barco Argus Information preview
Argus
Brand: Barco Pages: 6
Campbell CELL200 Series Quick Deploy Manual preview
CELL200 Series
Brand: Campbell Pages: 3
Paradox Magellan REM2 Reference And Installation preview
Magellan REM2
Brand: Paradox Pages: 2
Vag RIKO Operating And Maintenance Instructions Manual preview
RIKO
Brand: Vag Pages: 12
Eaton Cutler-Hammer LMR Instructions Manual preview
Cutler-Hammer LMR
Brand: Eaton Pages: 38
DeLaval MPCII Memo preview
MPCII
Brand: DeLaval Pages: 102
Cypress CY8C28 series Technical Reference Manual preview
CY8C28 series
Brand: Cypress Pages: 571
Conductrix Wampfler 0832 Installation Instructions Manual preview
0832
Brand: Conductrix Wampfler Pages: 23
Carel E2V Installation preview
E2V
Brand: Carel Pages: 2
Timotion TBB5 User Manual preview
TBB5
Brand: Timotion Pages: 9
Modine Manufacturing Airedale Sentinel Quick Start Manual preview
Airedale Sentinel
Brand: Modine Manufacturing Pages: 2
GEM 343 eSyDrive Operating Instructions Manual preview
343 eSyDrive
Brand: GEM Pages: 31
Yoshitake GPK-2001 Installation & Operation Manual preview
GPK-2001
Brand: Yoshitake Pages: 21
Oasis FV100 Series Instruction Manual preview
FV100 Series
Brand: Oasis Pages: 7
Danfoss VLT MCD 201 Installation Manual preview
VLT MCD 201
Brand: Danfoss Pages: 36
Ascon tecnologic vP4 Installation Manual preview
vP4
Brand: Ascon tecnologic Pages: 4
NEC mPD789101 User Manual preview
mPD789101
Brand: NEC Pages: 265

Brands by name

Popular brands

Load more brands