background image

2

Congratulations! We wish to thank you

 

for buying this cleaner. You have shown that you do not accept compromises: you want the best.

We have prepared this manual to enable to fully appreciate the qualities and high performance that this 

cleaner can offer you. Please read it completely before using the machine.

The CE mark on your cleaner shows that it has been constructed in compliance with the European 

Standards on safety.

We can also offer you a wide range of cleaning machines such as:

VACUUM CLEANERS,

 and a complete range of 

ACCESSORIES, CHEMICALS

 and 

DETERGENTS

 suitable 

for cleaning all kinds of surfaces.

Ask your Dealer for the complete catalogue of our products.

TRANSLATION OF ORIGINAL INSTRUCTIONS 

The text has been carefully checked, however any misprints should be notified to the manufacturer. 

The manufacturer also reserves the right to alter and update this publication without prior notice for the sake of 

product improvement. 

All reproductions of this manual, in whole or in part, are forbidden without the manufacturer's authorization. 

PREPARING THE CLEANER

Fitting the handlebar 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Fitting the lance. 

Fitting the rear tank. 

Water circuit connection. 

 

 

 

 

 

 

 

B

 

 

 

 

C

Electrical connection. 

30 mA 

 

Continue reading this manual without connecting the cleaner to the power mains and the water supply. 

Summary of Contents for HD140HOT

















Reviews: