Accessing the
Accessing the
video manual
video manual
Accessing the
Accessing the TD-02
TD-02
Owner’s Manual
Owner’s Manual
You can scan the
following 2D code to see
a quick start video. This
video explains the steps
for assembly.
Refer to the “Owner’s
Manual” (Roland website)
for details on how to use
TD-02.
Use this 2D code to
access the website.
1
2
Setup Guide
© 2022 Roland Corporation
Before using this unit, carefully read “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (in the leaflet “USING THE UNIT SAFELY” and in the TD-02K Setup Guide). After reading, keep the document(s) where
it will be available for immediate reference.
Check the included items
As soon as you open the package, check to see that all items are included. If anything is missing, please contact your dealer.
Assemble the drum stand
* If you will be using this drum stand for an extended period of time in the same location, we recommend that you use a drum mat (TDM series) made by Roland
to prevent the rubber feet from soiling the surface on which they are placed.
* The drum stand assembly procedure is for right-handed players. If you want to set up the stand for left-handed players, refer to “Assembly for left-handed
players” in the lower right.
For a left-handed setup
Assemble the drum stand as described in
“Assembly for left-handed players” in the “
2
Assemble the drum stand” section, and then
attach the parts and connect the cables as
shown in the illustration at right.
Ã
When you’ve finished making connections, turn on the power as described on the
back side of the “Quick Start” document, and verify that you can hear the sound.
This completes assembly and connections.
* Adjust the position and height of the pads and
pedals according to your build and preferences,
so that they are easy to play.
CY-5
CY-5
Hi-hat control pedal
Hi-hat control pedal
Kick pedal
Kick pedal
CY-5
CY-5
CY-5
CY-5
TD-02
TD-02
PD-4
PD-4
PD-4
PD-4
PD-4
PD-4
PD-4
PD-4
1.
Assembling the left and right arm sections
Right arm
Right arm
Left arm
Left arm
* Lay the left and right arm sections on the floor while assembling them.
Left arm section
1–1.
Use the drum key to loosen the bolt of the left leg
1
holder, and insert the left arm
2
.
Drum
key
Left
leg
1
Left arm
2
1–2.
Once the pipe is fully inserted, firmly tighten the bolt
with the drum key.
* Adjust the hi-hat rod holder of the left arm
2
and the L-shaped
pipe holder so that they are facing the same way, as shown in the
illustration.
Left arm
2
Hi-hat rod holder
L-shaped pipe holder
Right arm section
1–3.
Use the drum key to loosen the bolt of the right leg
6
,
and insert the right arm
5
.
1–4.
Once the pipe is fully inserted, firmly tighten the bolt
with the drum key.
Right arm
Right
leg
6
5
Holder
Bolt
2.
Attaching the left/right arm sections onto the center pipe
Right arm
Right arm
Left arm
Left arm
Center pipe
Center pipe
2–1.
Use the drum key to loosen the bolt of holder A, which
is attached to the center pipe
4
, and push it down to
the left. Insert the left arm you assembled in step 1 into
holder A.
Holder A
bolt
Center pipe
4
2–2.
Once the pipe is fully inserted, firmly tighten the bolts (2)
of holder A with the drum key.
Fully
tighten
Holder A
Temporarily tighten
2–3.
Use the drum key to loosen the bolt of holder B, and
insert the right arm you assembled in step 1 into holder
B of the center pipe
4
.
Right arm
Bolt
Holder B
Center pipe
4
2–4.
Once the pipe is fully inserted, tighten the bolts (2) of
holder B with the drum key.
Temporarily
tighten
Fully tighten
3.
Adjusting the vertical pipes
3–1.
Place the center pipe
4
upright, and adjust the angle so
that the drum stand can stand up by itself.
3–2.
Firmly tighten the bolts (2) of holders A and B that you
temporarily tightened in step 2.
Holder A and B bolts that were
temporarily tightened in step 2
3–3.
Make sure that the three vertical pipes remain fully
upright, and that the left/right arms are fully horizontal.
4.
Attaching the L-shaped pipe
L-shaped
L-shaped
pipe
pipe
L-shaped
L-shaped
pipe
pipe
4–1.
Use the drum key to loosen the bolt of the L-shaped
pipe holder for the left arm
2
, and insert the
L-shaped pipe
10
.
4–2.
Use the drum key to firmly tighten the bolt.
L-shaped pipe
10
L-shaped pipe holder
Bolt
Left arm
2
4–3.
Use the drum key to loosen the bolt of the L-shaped
pipe holder for the right arm
5
, and insert the
L-shaped pipe
10
.
4–4.
Use the drum key to firmly tighten the bolt of the
L-shaped pipe holder.
L-shaped pipe
10
Right arm
5
L-shaped pipe holder
Bolt
5.
Attaching the top pipe
5–1.
Loosen the hand knob on the top of the center pipe
4
.
5–2.
Rotate the holder so that the bolt faces forward, and
firmly tighten the hand knob.
Center pipe
Center pipe
4
Holder
Hand knob
Bolt
5–3.
Insert the top pipe into the holder, and use the drum key
to firmly tighten the bolt.
Top pipe
9
Bolt
Holder
6.
Attaching the tom pads (T1, T2) and cymbal rod holder
6–1.
Insert the toms through the top pipe
9
, and use the
drum key to firmly tighten the bolts (2).
9
T1
T1
T2
T2
Top pipe
Top pipe
Drum
key
6–2.
Attach the cymbal rod holder
8
onto the end of the top
pipe
9
, and firmly tighten the bolts (2) with the drum
key.
* Attach the cymbal rod holder so that its vertical bolt is on the back side
of the stand and the heads of its horizontal bolts are on the outside of
the stand, as shown in the illustration.
Bolt head
Bolt head
Drum
key
Drum
key
7.
Attaching the cymbal rod and hi-hat rod
7–1.
Lock the hi-hat rod holder in place so that its insertion
hole is facing to the back of the stand.
7–2.
Insert the hi-hat rod
3
, the ride cymbal rod
7
and the
crash cymbal rod
7
into the holders, and adjust the
position and direction of all holders as shown in the
illustration to complete the setup.
NOTE
The tip of the cymbal rod is sharp. Handle it with care.
Tilt towards the player
Cymbal rod
7
Face the slanted
side towards the
player
Hi-hat rod
3
NOTE
• Be careful not to get your fingers pinched by the movable parts when you set up or adjust the drum stand. If using this in a location where
children are present, be sure to provide adult supervision or guidance.
• Be sure that there is plenty of space to safely assemble this instrument.
• Do not use a power tool (e.g., an electric screwdriver) to assemble this instrument. Doing so may damage the screws.
• Do not overtighten the bolts.
• Be careful not to get grease from the bolts on your hands or other items.
Cabling diagram for the dedicated
connection cable
(As seen from the back)
4
Connection procedure
Connect the pads to the drum sound module (TD-02)
* Insert the plug firmly,
making sure it’s all the
way in.
1.
Connect the dedicated
connection cable to the drum
sound module as shown in the
illustration below.
Insert the connector all the
way, then turn the knobs to
lock it in place.
2.
Labels indicating the pad to
be connected are attached
to the dedicated connection
cable. Connect the cables by
referring to the illustration
at right.
* Use cable clips
11
to fasten the
cables so that they don’t obstruct
your playing.
We recommend attaching the
clips in the locations shown with
a .
Cabling diagram for the dedicated connection cable
(as seen from the back)
“CR2” is not used. You can use a
separately sold cymbal set (OP-
TD1C) to add more cymbals. If
you are not adding this, leave
the cap attached. Fasten it so
that it does not obstruct your
performance.
3
Attach the parts
NOTE
Be careful not to get your fingers pinched by the movable parts when you operate the drum
sound module holder, the hi-hat control pedal, the kick pedal or the cymbals. If using this in
a location where children are present, be sure to provide adult supervision or guidance.
TD-02K
Label
Assembly for left-handed players
If you want to use a left-handed setup, assemble the stand as
follows.
• Attach the hi-hat rod holder of the left arm
2
onto the right side of
the right arm
5
.
• Attach the L-shaped pipe
10
onto the L-shaped pipe holder of the
right arm
5
(insert the long pipe), and attach the hi-hat rod
3
onto the hi-hat rod holder.
• Attach the L-shaped pipe
10
(insert the short pipe) onto the
L-shaped pipe holder of the left arm
2
.
1
6
3
10
Left leg
Left leg
Right leg
Right leg
Hi-hat rod
Cymbal rod
L-shaped pipe
L-shaped pipe
7
Drum stand
No.
Name
Quantity
1
Left leg
1
2
Left arm
1
3
Hi-hat rod
1
4
Center pipe
1
5
Right arm
1
6
Right leg
1
7
Cymbal rod
2
8
Cymbal rod holder
2
9
Top pipe
1
10
L-shaped pipe
2
11
Cable clip
4
* To prevent the drum stand from tipping over,
do not position the stand leg pipes at either
end more than 1 meter apart.
1 m
Adjust the height of
the cymbal rod so that
the highest point of the
cymbal is 115 cm or less.
Attach the cymbal
rods so that they
face straight up, to
prevent the drum
stand from falling
over.
Adjusting the position of the cymbal
OK
Not
OK
Â
Hi-hat control pedal (FD-1)
Â
Kick pedal (KT-1)
Â
Cymbal pad for Hi-hat/ride/
crash (CY-5 x 3)
Â
Dedicated
connection cable
Â
AC adaptor
Â
Pad for Snare/tom (PD-4 x 4)
Â
Drum sound module
(TD-02)
Â
Drum sound
module holder
Â
Drum key
Drum sound module, pads, other items
* See “Hi-hat control pedal, kick pedal” on the back
side for how to distinguish between the pedals.
“CR2” is not used. You can use a separately sold cymbal set
(OP-TD1C) to add more cymbals. If you are not adding this,
leave the cap attached. Fasten it so that it does not obstruct
your performance.
115 cm
Not
OK
OK
Knob
Hi-hat control
Hi-hat control
pedal
pedal
Kick pedal
Kick pedal
PD-4
PD-4
((T1
T1))
PD-4
PD-4
((T2
T2))
CY-5
CY-5
((RD
RD))
CY-5
CY-5
((CR1
CR1))
TD-02
TD-02
PD-4
PD-4
((T3
T3))
CY-5
CY-5
((HH
HH))
PD-4
PD-4
((SNR
SNR))
Attaching the crash cymbal/ride cymbal (CY-5)
Insert the cymbal onto the top of the cymbal
rod.
Attaching the hi-hat (CY-5)
* Use the cymbal nut included with the drum stand to attach the hi-hat.
1.
Insert the cymbal so that the
stopper (convex portion) on the
hi-hat rod fits into the concave part
on the bottom of the cymbal.
2.
Tighten the cymbal nut enough
to prevent the pad from wobbling
when you strike it.
“Roland” logo on the
farther side
Cymbal nut
Rotation
stopper
(convex
portion)
Attaching the snare and
toms (PD-4)
Drum
key
L-shaped
L-shaped
pipe
pipe
Attaching the drum sound module (TD-02)
1.
Use the bolt for the drum sound module
holder to attach the drum sound module
to the holder.
Bolt
Drum sound module holder
2.
Loosen the bolt of the drum sound module
holder, attach the holder onto the top of
the center pipe and tighten the bolt.
1
2
3
4
6
7
8
10
11
5
9
CR1
T1
T2
SNR
CR2
T3
KIK
HHC
TD-02
HH
RD
CR1
HHC
KIK
RD
TD-02
HH
T1
T2
T3
SNR
CR2
