background image

Continuous level measuring system

NB 4000

Technical information / Instruction manual

page G 

Safety notes / Technical support

Notes

       •    Installation, maintenance and commissioning must be carried out only by qualified technical personnel.
       •    The product must be used only in the manner outlined in this instruction manual.

Special attention must be paid to warnings and notes as follows:

WARNING

Relates to a caution symbol on the product and means, that a failure to observe the necessary 
precautions can result in death, serious injury and/or considerable material damage. 

WARNING

Relates to a caution symbol on the product and means, that a failure to observe the necessary 
precautions can result in death, serious injury and/or considerable material damage.

This symbol is used, when there is no corresponding caution symbol on the product.

A failure to observe the necessary precautions can result in considerable material 
damage. 

CAUTION

Safety symbols

In manual and on 

product

Description 

CAUTION: refer to related documents (manual) for details.

Earth (ground) Terminal

Protective Conductor Terminal

Technical support

Please contact your local supplier (see www.uwt.de for address). Otherwise you can contact:

UWT GmbH 

 

 

Tel.  0049 (0)831 57123-0

Westendstr. 5 

 

 

Fax. 0049 (0)831 76879

87488 Betzigau   

 

[email protected]

Germany 

 

 

www.uwt.de

Nivobob

®

1

2

3

4

5

6

7

8

9

10

11

12

NB 4000

gi010413

2

Summary of Contents for Nivobob NB 4000























Reviews: