Utax P-4531DN Operation Manual Download

Page: 85 / 352

4-7

Operation Panel

Using the Menu Selection System

Menu Selection System

This section explains how to use the menu selection system.

[Menu]

on the operation panel allows you to use the menu to configure the printer settings to your specific needs. Settings

can be made when

Ready to print.

Please wait.

Processing.

Sleeping...

is indicated on the printer

message display.

Entering the Mode Selection Menu

Press

[Menu]

when

Ready to print.

is indicated on the printer message display.

The mode selection menu is displayed.

Note

Settings that are received from application software and the printer driver will take priority over settings made

in the operation panel.

Paper Source:

MP Tray

Cassette 1

Ready to print.

Status

Toner

Scroll page

Scroll line

An asterisk (*) is displayed
to the left of the currently
selected setting.

Menu:

Counter

Exit

Paper Settings

Report

The directions of usable
arrow keys are shown on
the screen displayed.

Menu:

Network

Exit

Print Settings

Device Common

Print Settings:

MP Tray Priority

Exit

Auto Cass.Change

Paper Source

Summary of Contents for P-4531DN

































































































































































































































































































































































Search results

Summary of Contents for P-4531DN

Reviews:

Related manuals for P-4531DN

Brands by name

Popular brands

Utax P-4531DN, Operation Manual

Search results

Summary of Contents for P-4531DN

Reviews:

Related manuals for P-4531DN

Brands by name

Popular brands