Utax P-4531DN Operation Manual Download | Manualshive

Page: 279 / 352

background image

7-7

Maintenance

Replacing the Waste Toner Box

Replace the waste toner box when the

Waste toner box is full.

message is displayed and when replacing the toner

container. A new waste toner box is included with the toner kit. The waste toner box needs to be replaced before the printer
will operate.

1

Open the left cover.

2

While holding the waste toner box, press the lock lever and then
gently remove the waste toner box.

3

Close the cap to the old waste toner box after removing the box from
the printer.

4

To prevent toner from spilling, put the old waste toner box in the
plastic bag (contained in the toner kit) and discard it later according
to the local code or regulations for waste disposal.

5

Open the cap of the new waste toner box.

CAUTION

Do not attempt to incinerate the Toner Container. Dangerous sparks may cause burns.

Left Cover

Lock Lever

Note

Remove the waste toner box as gently as possible so

as not to scatter the toner inside. Do not let the opening of the
waste toner box face downward.

Old Waste
Toner Box

Cap

Plastic Bag

Cap

New Waste
Toner Box

«
...
277
278
279
280
281
...
»

Summary of Contents for P-4531DN

































































































































































































































































































































































Reviews:

No comments

Related manuals for P-4531DN

SPP 2020 - Photo Printer - 20 Sheets

Brand: Samsung Pages: 81

Brand: Samsung Pages: 98

Brand: Samsung Pages: 6

Brand: Samsung Pages: 203

Brand: Samsung Pages: 264

Brand: Samsung Pages: 228

Brand: Samsung Pages: 211

Brand: Samsung Pages: 5

Brand: Samsung Pages: 92

Brand: Samsung Pages: 75

Brand: Samsung Pages: 11

Brand: Samsung Pages: 206

ML 3050 - B/W Laser Printer

Brand: Samsung Pages: 103

ML 3050 - B/W Laser Printer

Brand: Samsung Pages: 215

Brand: Samsung Pages: 2

CLP 510N - Color Laser Printer

Brand: Samsung Pages: 266

550N - CLP Color Laser Printer

Brand: Samsung Pages: 296

Brand: Samsung Pages: 276

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands