USSC Logwood C242 Owner'S Manual Download Page 1

Page: 1 / 12

CAUTION!

Read All Instructions Care-

Read All Instructions Care-
fully Before Starting The In-

fully Before Starting The In-

fully Before Starting The In-
stallation or Operating This

stallation or Operating This

stallation or Operating This
Heater.

Heater.

DO NOT USE THIS HEATER

IN A MOBILE HOME OR TRAILER

SAVE THIS MANUAL FOR FUTURE REFERENCE

THIS MANUAL WILL HELP YOU TO OBTAIN EFFICIENT, DEPENDABLE SERVICE FROM THE HEATER, AND ENABLE

THIS MANUAL WILL HELP YOU TO OBTAIN EFFICIENT, DEPENDABLE SERVICE FROM THE HEATER, AND ENABLE
YOU TO ORDER REPAIR PARTS CORRECTLY. KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

YOU TO ORDER REPAIR PARTS CORRECTLY. KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

UNITED STATES STOVE COMPANY

227 Industrial Park Road

P.O. Box 151

South Pittsburg, TN 37380

(423) 837-2100

COMPANY

ITE

D STATES STOV

851476 A

Owners Manual

Logwood C242

TESTED TO

UL 1482

CAN/ULC S627

Summary of Contents for Logwood C242













Search results

Summary of Contents for Logwood C242

Reviews:

USSC Logwood C242, Owner'S Manual, Page: 1 / 12

Search results

Summary of Contents for Logwood C242

Reviews: