background image

                          USR-WIFI232-B2 Hardware Manual                                                 

www.usriot.com

 

 

 
Jinan USR IOT Technology Limited                                                    9 / 9                                                                     

 

h.usriot.com

 

Frequency   

2.4~2.5GHz 

Impedance 

50 Ohm 

VSWR 

2 (Max) 

Return Loss 

-10dB (Max) 

Connector 

I-PEX or populate directly 

 

 

 

 

 

3. Contact 

Company: Jinan USR IOT Technology Limited 

Address:   Floor  11,  Building  No.1,  No.1166,  Xinluo  Street,  Gaoxin  District,  Jinan  city,  Shandong  province, 

250101 China 

Tel: 86-531-88826739 

Web: 

www.usriot.com

 

 

Support: 

h.usriot.com

   

 

Email: 

[email protected]

 

 

4. Disclaimer 

This document provide the information of USR-WIFI232-B2 

products, it hasn’t been granted any intellectual 

property license by forbidding speak or other ways either explicitly or implicitly. Except the duty declared in 
sales terms and conditions, we don’t take any other responsibilities. We don’t warrant the products sales and 
use explicitly or implicitly, including particular purpose merchantability and marketability, the tort liability of any 

other patent right, copyright, intellectual property right. We may modify specification and description at any 

time without prior notice.     

5. Update History   

2017-07-27    V1.0.0 created.   

Summary of Contents for USR-WIFI232-B2










Reviews: