background image

Intended use 

11/20

Fl Remote Set

Intended use  

Please observe the instructions in this operating manual as well as 
the operating conditions and permissible data according to the data 
sheet  to  ensure  that  the  system  functions  properly  and  remains 
operational  for  a  long  time.  In  case  of  non-observance  of  these 
instructions as well as in case of unauthorized interventions in the 
system,  any  liability  on  our  part  is  void,  and  the  warranty  on  the 
system and accessories is also void!  

 

The Fl Remote Set consists of three 433 Mhz radio water 
sensors (modified Sonoff DW2-RF door sensors), a radio remote 
control and a KTNNKG 2 channel radio receiver. 

The  radio  receiver  must  be  located  at  the  installation  site  of 
Fl.  The  wireless  water  sensors  can  be  up  to 50  meters 
away (depending on the environment) (bathroom, kitchen, etc.). 

If  a  radio  water  sensor  detects  conductive  drinking  water, 
Fl  is  immediately  shut  off  via  the  radio  receiver.  Any 
number of wireless water sensors can be taught-in. 

The learnable radio remote control can shut off the water or reset 
the Fl. 

The Fl Remote Set contains additional parts to split the 
Fl  I/O  connector.  This  allows  you  to  connect  additional 
Fl accessories if required. 

An alarm reset can be done via the connected Fl or via 
the second channel of the radio receiver via radio remote control. 

 

Any  other  or  further  use  is  considered  to  be  improper.  usetech 
GmbH shall not be liable for any damage resulting from such use. 
The risk is borne solely by the user. 

 

 

Summary of Contents for FlowTimer+ Remote Set























Reviews: