The chart below shows the functions of special keys for your cable box and
program guide. See the cable box manual for further details.
© 1999 US Electronics Components Corp.
All rights reserved
Part Number USE17837, version 1.0
9903
User’s Guide for the
UG3DIGI
3-in-1 Cable TV
RemoteControl
If you have a TV with a remote control,
we recommend that you plug its power
cord directly into a wall outlet if avail-
able (your cable installer may select an
alternate setup).
Make sure to set your TV to channel 2, 3,
or 4 as directed by your cable company.
Press the
[VCR]
button, then the
[SETUP]
button on the remote.
Enter the 3-digit VCR code for your brand of VCR listed in the “VCR
codes” chart on the other side of this manual by pressing the
appropriate buttons on the numeric key pad.
Press the
[SETUP]
button again to save the code. The red indicator
light at the upper left-hand corner of your remote will flash 3 times if
these steps were followed correctly.
Press the
[VCR]
button again to test the code you‘ve entered. The
VCR should turn on or OFF each time the
[VCR]
button is pressed. If
the VCR doesn’t turn on and OFF, repeat this VCR setup procedure
with the next code listed in the “VCR codes” chart (section 5) .
Press the
[TV]
button, then the
[SETUP]
button on the remote.
Enter the 3-digit TV code for your brand of TV listed in the “TV codes”
chart.
Press the
[SETUP]
button again to save the code. The red indicator
light at the upper left-hand corner of your remote will flash 3 times if
these steps were followed correctly.
Press the
[TV]
button again to test the code you‘ve entered. The TV
should turn on or off each time the
[TV]
button is pressed. If the TV
doesn’t turn on and off, repeat this TV setup procedure with the next
code listed in the “TV codes” chart (section 6).
BEFORE YOU
BEGIN
1
2
3
!
Weak batteries may disrupt
normal operation of the remote.
We recommend that you use
only AA alkaline batteries.
4
b
c
d
e
Before you can program or operate the
remote control, you must install two AA
Alkaline batteries.
Step 1:
Remove the battery compartment cover
on the back of your remote control. A
screwdriver may be required to pry the
cover off.
Step 2:
Check battery polarity carefully, and
install the batteries as shown in the
illustration below
Step 3:
Replace the battery compartment cover.
INSTALL
BATTERIES
KNOW YOUR
REMOTE
SETTING UP
YOUR REMOTE
A
FOR YOUR VCR
B
FOR YOUR TELEVISION
C
FOR YOUR CABLE BOX
b
c
d
e
Press the
[CABLE]
button, then the
[SETUP]
button on the remote.
Enter the 3-digit cable box code:
[0] [0] [0]
.
Press the
[SETUP]
button again to save the code. The red indicator
light at the upper left-hand corner of your remote will flash 3 times if
these steps were followed correctly.
Press the
[CABLE]
button again to test the code you‘ve entered. The
cable box should turn on or off each time the
[CABLE]
button is pressed.
If the cable box doesn’t turn on and off, try entering the code again.
b
c
d
e
IMPORTANT
NOTE
US Electronics provides these function descriptions as a general guide to allow you to become more familiar with your cable box. Refer to your cable box manual for descriptions of specific functions.
Following these steps allows the remote to control volume through your cable box. If
you would like volume to be controlled through your TV, perform
step C
before
step B
.
If you have a combination TV/VCR, use a code from the VCR Codes section (volume will
be controlled only through the cable box).
www.uselectronics.com
VISIT US ON THE WEB
You can find programming instructions and codes
for all of our remote controls, as well as information
about our other products on our website:
I
N
F
O
Memory Lock
™
is an exclusive
technology that saves the device codes
that are programmed into the remote,
even when the batteries are removed.
MORE
INFO
NUMERIC KEYS
These keys allow you to enter
the channel you want to view.
You will also use them
to setup the remote
CABLE BOX
FUNCTION KEYS
See the chart below for a
description of the key
functions. Note the location
of the
[SETUP]
key — you
will use it when you setup
the remote.
VCR CONTROLS
These keys operate standard
VCR or VOD functions
depending on the position of
the VCR/VOD switch.
Note:
Press the
[REC]
key twice to
start recording on your VCR.
FAV
cycles through your favorite channels
LOCK
used for Parental Control
SETUP
used to setup the remote
TV/VCR
switches the VCR between TV and VCR mode
MUTE
turns volume off
MENU
displays the main on-screen display menu
GUIDE
displays the program guide
SEL
selects various options and tunes programs from the program guide
CURSOR KEYS
navigate through on-screen guides
INFO
displays channel and program information
EXIT
exits the on-screen display menus
PAGE +/-
pages through on-screen menu and program guide screens
DAY +/-
moves the program guide one day forward and backward
LAST
recalls the last channel that was viewed
MUSIC/ENTER
switches between cable TV and Music Choice™
A, B, C
future use
HELP
displays help for the on-screen display
VCR/VOD
switches the VCR controls into Video-on-Demand controls
NOTE
Depending on the
configuration of your
cable box, certain
functions listed here may
or may not be functional.
CURSOR KEYS
