background image

Page 8

MRX-10 A

DVANCED

N

ETWORK

S

YSTEM

C

ONTROLLER

Federal Communication Commission
Interference Statement

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a res-

idential installation. This equipment generates, uses and can radiate radio fre-

quency energy and, if not installed and used in accordance with the instruc-

tions, may cause harmful interference to radio communications. 

However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or tele-
vision reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one more of the
following measures:

u

Reorient or relocate the receiving antenna.

u

Increase the separation between the equipment and receiver.

u

Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

u

Consult the dealer or an experienced radio/TV technician for
help.

Warning!

Changes or modifications not expressly approved by the manufacturer could

void the user's authority to operate the equipment.

Note : The manufacturer is not responsible for any Radio or TV interference

caused by unauthorized modifications to this equipment. Such modifications

could void the user's authority to operate the equipment.

FCC Caution

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference,

and (2) this device must accept any interference received, including interference

that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible

for compliance could void the authority to operate equipment.

The antenna(s) used for this transmitter must not be co-located or operating in

conjunction with any other antenna or transmitter.

Federal Communication Commission (FCC) Radiation Exposure Statement

The device and the antenna for this device must be installed to ensure a

minimum separation distance of 20 cm more from a person's body. Other

operating configurations should be avoided.

Summary of Contents for MRX-10















Reviews: