Package Contents
Warnings and Cautions
1of2
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Figure 4
A
Fixture
Body
x 1
Tools Required:
Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Estimated Assembly Time:
30-45 minutes
Preparation:
Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
Fixture can only be mounted in the direction indicated on page 2.
Bulb Recommended:
(3) Candelabra Base T8 Bulb 40W (supplied), 60W Maximum.
STEP 1
Install Inner Backplate
-
A. Pass the supply wires through the Crossbar Assembly (I). Attach the
Crossbar Assembly (I) to the Outlet Box with the head of the Green
Ground Screw facing you. Secure it with Outlet Box Screws (not
included). Tighten until snug
.
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
White wire
from supply
Ribbed side wire
from fixture
Black wire from
supply (or Red)
Smooth side wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 3
H
Crossbar
Assembly
x 1
Supply Wires with
Ground Wire
H
Outlet Box Screws
(not included)
Outlet Box
Figure 1
STEP 4
Install Fixture Body
-
A. Carefully tuck all wires into the
outlet box and position the
backplate of Fixture Body (A) over
the outlet box. Align the holes in the
backplate with the mounting
screws. Place caulk (not supplied)
into the previously removed
mounting balls and then attach
Fixture Body (A) using the mounting
balls. Hand tighten until snug.
Figure 2
Hex Nut and
Lock Washer
H
Mounting
Ball
Mounting
Screw
A
B
Candle
Cover
x 3
C
Bulb
x 3
D
Shade
x 1
E
Cage
x 1
F
Mounting
Ball
x 2
G
Water Proof
Washer
x 2
STEP 2
Fit Fixture Body to Crossbar Assembly
-
A. Remove mounting balls from the Crossbar Assembly (H). Fit the
Fixture Body (A) Crossbar Assembly (H) and secure with mounting
balls. Note: The backplate of the Fixture Body (A) should be snug
against the wall surface and the mounting balls. If not, adjust the
length of the nipple on the Crossbar Assembly (H) by unscrewing the
preassembled hex nut and lock washer and then screwing the
mounting screws in or out of the crossbar until the correct length is
achieved. Once the backplate of the Fixture Body (A) is secure,
remove the mounting ball and Fixture Body (A) and proceed to Step 3.
H
Mounting
Ball
Mounting
Screw
A
STEP 5
Install Candle Cover
and Bulb
-
A. Place Candle Cover (B) over the
Socket properly.
B. This fixture uses candelabra
bulb with standard screw base.
Maximum 60 watts.
C. Insert bulb and screw snugly into
place.
B
C
Socket
Figure 5
Installation Instructions:
UQL
1
123
www.urbanambiance.com
