background image

9.

Installing the Light Kit and Glass Shade

CAUTION:

 Before starting installation,

disconnect the power by turning off the circuit 
breaker or removing the fuse at fuse box. 
Turning power off using the fan switch is not 
sufficient to prevent electric shock.

Step 1.

 Remove 1 of 3 screws from the posts of

the mounting plate and keep it for future use. 
Loosen the other 2 screws. (Do not remove) 

Step 2.

 While holding the LED light kit under

the fan motor assembly, make the 2-pin wire 
connections: (Fig. 16)
- White to white
- Black to black

Step 3.

 Place the key holes in the light kit over

the two screws previously loosened from the 
mounting plate. Turn the light kit until the light 
kit locks in place at the narrow section of the 
key holes. (Fig. 16)

Step 4.

 Securely tighten the two mounting

screws previously loosened and the one 
previously removed. 

Step 5.

 Raise glass shade up against the light kit

and secure it to fan by turning glass clockwise 
until snug. DO NOT OVERTIGHTEN. 

Figure 16

LED 

light kit

Wire connectors

Screws

Mounting

plate

Glass 

shade

Installing the battery

Install a 12V battery (included) into the remote 
control. To prevent damage to the remote control, 
remove the battery if not used for long periods. 
(Fig. 17)

Figure 17

Summary of Contents for UHP9000
















Reviews: