Upright X Series Service & Parts Manual Download Page 44

Page: 44 / 164

Page 3-16

Maintenance

3.12 - Hydraulic Pump

X Series Work Platform

3.12 H

YDRAULIC

UMP

Figure 3-18: Hydraulic Pump

EMOVAL

NOTE:

If the hydraulic tank has not been drained,

suitable means for plugging the hoses should be
provided to prevent excessive fluid loss.

1. Mark, disconnect, and plug the hose

assemblies.

2. Loosen the capscrews and remove the

pump assembly from the motor.

NSTALLATION

1. Lubricate the pump shaft with general pur-

pose grease and attach the pump to the
motor with the capscrews.

2. Using a criss-cross pattern, torque each capscrew a little at a time until all of the capscrews

are torqued to 20 Ft/Lbs (27 Nm).

3. Unplug and reconnect the hydraulic hoses.

4. Check the oil level in the hydraulic tank before operating the work platform.

3.13 H

YDRAULIC

RIVE

OTORS

AND

UBS

EMOVAL

1. Block the rear wheels to prevent the machine from rolling.

2. Use a 1 ton (1000 Kg) capacity jack to raise the front of the machine. Place two 1 ton (1000

Kg) jackstands beneath the machine for support. Remove the jack.

3. Remove the wheel bolts and wheel.

4. Remove the cotter pin, slotted nut, hub, and shaft key.

NOTE:

Before disconnecting any hoses, thoroughly clean off all the outside dirt around the fittings.

IMMEDIATELY plug the port holes after disconnecting the hoses and before removing the motor from the
vehicle.

5. Tag, disconnect and plug the hose assemblies to prevent foreign material from entering.

6. Remove the locknuts, capscrews, and drive motor.

Figure 3-19: Drive Motor

NSTALLATION

1. Position the drive motor in the wheel

yoke, and secure it with capscrews and
locknuts.

2. Install the shaft key, hub, and slotted

nut. Torque the slotted nut to 140-160
Ft/Lbs (190-217 Nm). Install a new cot-
ter pin. DO NOT back off the nut to
install the cotter pin.

3. Remove the plugs from the hose

assemblies and reconnect them to the
drive motor.

4. Install the wheel and secure with wheel

bolts. Torque to 80 Ft/Lbs (108 Nm).

5. Remove the jackstands, lower the jack,

and remove. Operate the drive system
and check for leaks.

Pump

1.Drive Motor
2.Wheel Yoke
3.Slotted Nut

4.Wheel
5.Cotter Pin
6.Hub

060571-005

Summary of Contents for X Series





































































































































































Search results

Summary of Contents for X Series

Reviews:

Related manuals for X Series

Brands by name

Popular brands

Upright X Series, Service & Parts Manual

Search results

Summary of Contents for X Series

Reviews:

Related manuals for X Series

Brands by name

Popular brands