Upright X Series Service & Parts Manual Download Page 18

Page: 18 / 164

Page 2-6

Operation and Specifications

2.3 - Operation

X Series Work Platform

MERGENCY

OWERING

Figure 2-5: Emergency Lowering Valve Handle

The Emergency Lowering Valve for the
X20N, X20W, and X26N is located at the
rear of the machine, above the charger.

The Emergency Lowering Valve for the
X31N is located at the rear of the
machine, to the left of the charger.

1. Open the Emergency Lowering

Valve by pulling and holding the
knob.

2. To close, release the knob. The

platform will not elevate if the
Emergency Lowering Valve is
open.

W A R N I N G

If the platform should fail to lower, NEVER climb down the elevating
assembly.

Emergency Lowering Knob

060571-005

Summary of Contents for X Series





































































































































































Search results

Summary of Contents for X Series

Reviews:

Related manuals for X Series

Brands by name

Popular brands

Upright X Series, Service & Parts Manual

Search results

Summary of Contents for X Series

Reviews:

Related manuals for X Series

Brands by name

Popular brands