© UPLIFT Desk
• 1-800-349-3839 • [email protected] • www.upliftdesk.com
®
E7 Electric Standing Desk Converter Instructions
UDA115
UDA115/R01
90.014.01.0500v.C
Package contents
Flat head screws
(M6x14; qty 8)
Pan head screws
(M6x14; qty 2)
VESA mount
VESA bracket
Slot cover
Keypad
Power cable
Connecting cable
Base
Lifting
column
Housing
Keyboard tray
bracket
Keyboard tray
Worksurface
Worksurface
bracket
Pan head screws
(#10-24x5/8’’; qty 13)
Keypad
Power cable
Connecting
cable
Pan head screws
(M6x10; qty 4)
Pan head screws
(M4x12; qty 4)
VESA screw
(qty 1)
Cable clips
(qty 2)
Step 1
Place the base on your desk, with the front lined up with the front edge
of your desk. First
(a)
Attach the Lifting column to the Base using four (4)
M6x14 Flat head screws. Make sure the vertical column is facing towards
the front. Next,
(b)
Attach the Worksurface bracket to the front of the
Lifting column using four (4) M6x10 Pan head screws.
Step 2
Plug the Lifting column’s cable into the Connecting cable, and plug the
Connecting cable into the Control box. Also, plug the Keypad and Power
cable into the Control box, and finally plug the Power cable into a 120
Vac wall outlet. Press the “up” arrow on the Keypad to raise the Work-
surface to a higher level for Steps 3 and 4.
Note:
If surface does not rise perform the reset instructions
in the TROUBLESHOOTING section on page 4.
Step 3
Unplug the Keypad only! Feed the end of the Keypad’s wire through
the top side of the Worksurface and fit the Keypad into the pocket as
shown. Press Keypad cable into the wire channel on the underside of
the Worksurface. Attach Worksurface onto the Worksurface bracket
using five (5) #10-24x5/8’’ Pan head screws. Plug the Keypad back into
the Control box.
[x] POWER CABLE
[x] CONNECTING CABLE
(get from FRM200 instructions)
VESA screw
#10-24x1/2’’
Pan Head
M5x10
Pan Head
M6x10
Flat Head
Socket cap
[x] POWER CABLE
[x] CONNECTING CABLE
(get from FRM200 instructions)
VESA screw
#10-24x1/2’’
Pan Head
M5x10
Pan Head
M6x10
Flat Head
Socket cap
[x] POWER CABLE
[x] CONNECTING CABLE
(get from FRM200 instructions)
VESA screw
#10-24x1/2’’
Pan Head
M5x10
Pan Head
M6x10
Flat Head
Socket cap
[x] POWER CABLE
[x] CONNECTING CABLE
(get from FRM200 instructions)
VESA screw
#10-24x1/2’’
Pan Head
M5x10
Pan Head
M6x10
Flat Head
Socket cap
[x] POWER CABLE
[x] CONNECTING CABLE
(get from FRM200 instructions)
VESA screw
#10-24x1/2’’
Pan Head
M5x10
Pan Head
M6x10
Flat Head
Socket cap
[x] POWER CABLE
[x] CONNECTING CABLE
(get from FRM200 instructions)
VESA screw
#10-24x1/2’’
Pan Head
M5x10
Pan Head
M6x10
Flat Head
Socket cap
[x] POWER CABLE
[x] CONNECTING CABLE
(get from FRM200 instructions)
VESA screw
#10-24x1/2’’
Pan Head
M5x10
Pan Head
M6x10
Flat Head
Socket cap
[x] POWER CABLE
[x] CONNECTING CABLE
(get from FRM200 instructions)
VESA scr
ew
#10-24x1/2’
’
Pan Head
M5x10
Pan Head
M6x10
Fla
t Head
Socket cap
[x] POWER CABLE
[x] CONNECTING CABLE
(get from FRM200 instructions)
VESA scr
ew
#10-24x1/2’
’
Pan Head
M5x10
Pan Head
M6x10
Fla
t Head
Socket cap
[x] POWER CABLE
[x] CONNECTING CABLE
(get from FRM200 instructions)
VESA screw
#10-24x1/2’’
Pan Head
M5x10
Pan Head
M6x10
Flat Head
Socket cap
(a)
(a)
(b)
(b)
Step 4
Attach the Keyboard tray bracket to the Worksurface using four (4) #10-
24x5/8’’ Pan head screws. Then attach the Keyboard tray to the Keyboard
tray bracket also using four (4) #10-24x5/8’’ Pan head screws.
Caution:
Make sure that Keyboard tray of the assembled unit is clear of the
desk edge. When the unit is at it’s lowest position, the Keyboard tray will be
lower than the desk’s surface.
Step 5
Take a moment to group your wires tightly together, to prevent them from
splaying too widely, getting caught in moving parts, or interfering in Step 6.
We recommend using the two (2) Cable clips with adhesive here:
(a) Above the Control box to keep the Power cord close to the Lifting
column. For additional securing, the cable can run behind the Control box.
(b) About 2’’ below the Control box, on the top segment of the lifting column
(as shown). Leave slack to allow the lifting column to rise all the way up.