background image

 

 FLORIDA-PNEUMATIC.COM 

 

Please contact 1-800-356-3392 for further assistance.

Universal Tool

4 Bolt Chipping Hammers

General Safety Information & Replacement Parts

WARNING:

 Risk of injury to persons. Read and 

understand operation instructions.  Always become familiar 
with all the instructions and warnings before operating any 
pneumatic tool.

TABLE OF CONTENTS

General Safety Information    .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 2 
Air Compressor and Air Tool Safety  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 2-3 
Tool Specifications   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 3-4
Installation   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 4
Maintenance / Lubrication   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 4
Operation .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 5
Troubleshooting   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 6
Warranty   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 6
Service Parts  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 7 

UT8651R / UT8651H 

1" Stroke Chipping Hammers

UT8651R / UT8651H
UT8652R / UT8652H 
UT8653R / UT8653H 
UT8654R / UT8654H 

UT8652R / UT8652H 

2" Stroke Chipping Hammers

UT8653R / UT8653H 

3" Stroke Chipping Hammers

UT8654R / UT8654H 

4" Stroke Chipping Hammers

WARNING

:

 This product contains chemicals known to 

the State of California to cause cancer and birth defects or 
other reproductive harm. Wash hands after handling.

WARNING

:

 This product contains lead, a chemical known to 

the State of California to cause cancer and birth defects or 
other reproductive harm. Wash hands after handling.

Summary of Contents for UT8651R









Reviews: