![background image](http://html1.mh-extra.com/html/universal-remote-control/ur-j550tve/ur-j550tve_operating-manual_1058829001.webp)
Universal Remote Control, Inc.
www.universalremote.com
OEE-0017D Rev 03(05/14/02)
This remote control is preprogrammed
to operate CABLE Box.
Please program it for your TV by
following the instructions shown below.
The remote control uses AAA batteries.
Please be sure to match the batteries
with the (+) and (- ) markings inside the
battery compartment during installation.
The remote control is preprogrammed to
control VOLUME and MUTE functions
through your TV. To switch VOLUME and
MUTE functions to your Cable Box:
STEP1
Press [ ] and [MUTE]
buttons simultaneously until
red light is on.
STEP2
Press [] button.
STEP3
Press [ ] button.
To return to the TV’s VOLUME, press
[TV POWER] button.
*Tip:
Red light will blink twice.
Set-up for advanced functions
A. To turn on your TV and Cable at the
same time with
button:
STEP1
Press [ ] and [0] buttons
simultaneously until the red
light is on.
STEP2
Press [CH +] button.
Set-up for your Cable Box
The remote control is preprogrammed
to control your cable box. If it does
not work properly, please set-up the
right code by using the three-digit
code or searching method.
If you have a TV with a remote
control, we recommend that you plug
its power cord directly into a wall
outlet if available (your cable installer
may select an alternate setup)
Operation
If red light does not blink when
you press keys the operation is
intermittent:
Make sure the batteries are inserted
correctly.
Replace old batteries with two new
AAA batteries. Please do not mix old
batteries with new ones.
Operating Manual
for 2 in 1 Cable TV
Remote Control
UR-J550TVE
Instructions
Batteries
Programming your remote control
Set-up for your VOLUME control
Helpful hints
STEP3
Point the remote control toward
the TV and enter the three-digit
code from the code table. If
there is more than one code
number assigned to your TV
brand, try one code number at a
time until the TV turns off right
after you entered the number.
Searching Method
Press [CH +] button and hold until the
TV turns off. As soon as the TV turns
off, release [CH+] button.
*Tip :
You can confirm the power off and
on by pressing [MUTE] button.
STEP4
Press [TV POWER] button to
store the three-digit code.
*Tip:
Red light will blink twice.
Three-digit code :
Setup for your cable box
No setup is required. The remote control is
preprogrammed to operate your cable box.
Setup for your TV
Find your TV brand and its three-digit
code on the back of this manual. If the
TV brand is not listed, please use the
Searching Method in
STEP3
.
STEP1
Turn on your TV manually.
*Tip :
If you have RCA TV, don’t turn
on the TV.
STEP2
Press [TV POWER] and [MUTE]
buttons simultaneously until the
red light is on.
*Tip:
Red light will blink twice
The [ ] button sends out the TV
and CABLE power commands if you
press the [ ] button.
To return to the original function, press
the [CH-] button in the
STEP2
.
B. Recalling the TV Three-digit code :
STEP1
Press [TV POWER] and [MUTE]
buttons simultaneously until the
red light is on.
STEP2
Press [VOLUME -] button.
The red light will blink a number of
times indicating the number of each
digit of the code. Each digit is
separated by one second interval of
red light being off.
*Tip:
One blink, three blinks and 10
blinks, indicates the code
number 130.
Press arrow gently &
pull down to remove cover
Install two AAA alkaline
batteries as shown here