![background image](http://html1.mh-extra.com/html/universal-remote-control/4-function-dtv-remote-control/4-function-dtv-remote-control_operating-instructions_1058947001.webp)
Universal Remote Control, Inc.
www.universalremote.com
OCE-0002A Rev 12(05/31/07)
Operating Instructions
For 4 Function
DTV Remote Control
The remote control is designed to
operate the DTV series set top boxes
and the majority of TV, VCR/DVD and
AUDIO equipment on the market.
Introduction
1
Default State :
Device Default: DTV Cable box.
Volume Default: TV volume and mute
through the TV, with the option of
controlling volume and mute through
the Cable box or Audio. Refer to Section
F
for programming the volume and mute
through your Cable box or Audio.
System On/Off button:
This button is designed to send out
power commands for two, three or all
four devices with one button press.
Please refer to section
E
for details.
Operations
4
Replacing Batteries
2
Before you program or operate the
remote control, you must install two
new AA alkaline batteries.
STEP1
Remove the battery compartment cover
on the back of your remote control.
STEP2
Check battery polarity carefully,
and install the batteries as shown
in the illustration below.
STEP3
Replace the battery compartment cover.
Button Functions
3
Programming the Remote Control
5
A. Programming For Your Devices.
The remote control can be programmed by pressing in a three digit code number
that corresponds to particular manufacturers and brands of Audio/Video
equipment. The three-digit code numbers are listed in the code table of the
instruction manual.
STEP1
Turn on the equipment you wish to program. (TV, VCR, DVD or AUDIO).
STEP2
Press the [DEVICE] button (TV , VCR or AUD) to be programmed and the
[SELECT] button simultaneously for 3 seconds. The device LED will turn
on indicating the unit is ready to be programmed.
*Tip
: The device LED will light on for 20 seconds. The next step must be entered
while the LED is on.
STEP3
Point the remote control toward the equipment and enter the three-digit
code number assigned to your brand from the code tables.
*Tip
: The equipment will turn off when
the correct three-digit code
number has been entered. You
can verify you have selected the
correct code by pressing the
[MUTE] button, the equipment
should turn on or turn off.
*Note :
If there is more than one
three-digit number listed for your
brand, try one code number at a time
until your equipment turns off.
STEP4
Store the three-digit code
number by pressing the same
[DEVICE] button once again.
The device LED will blink
twice to confirm that the
code has been stored.
*Note :
Try all the functions on the
remote control. If any of the functions
do not work as they should, repeat from
Step 2 using the next three-digit code
number from the same brand list. Make
sure that the VCR/VOD button is in the
VCR position when using your VCR.
B. Auto Search Method.
If the three-digit code numbers assigned
to your brand do not turn off your
equipment or the code tables do not list
your brand, you can use the
Auto Search
Method to find the correct three-digit
code number for your equipment by the
following steps:
STEP1
Turn on the equipment you
wish to operate.
STEP2
Press the [DEVICE] button (TV,
VCR or AUD) to be programmed
and the [SELECT] button
simultaneously for 3 seconds.
The device LED will turn on.
*Tip
: The device LED will light on for
20 seconds. The next step must
be entered while the LED is on.
STEP3
Press the [CH+] or [CH-] button
one step at a time or keep it
pressed. The remote will emit
a series of Power ON/OFF
commands. Release the [CH+]
or [CH-] button as soon as the
equipment turns off.
*Tip
: You can verify that you selected
the correct code by pressing the
[MUTE] button. The TV should
either turn on or turn off.
STEP4
Press the same [DEVICE]
button to store the code. The
Device LED will blink twice to
confirm that the code has
been stored.
C. To Find the Three Digit
Code Number That was
Stored in the Device.
STEP1
Press the [DEVICE] button (TV,
VCR or AUD) you wish to verify
and the [SELECT] button
simultaneously for 3 second.
The device LED will turn on.
*Tip
: The device LED will light on for
20 seconds. The next step must
be entered while the LED is on.
STEP2
Press the [INFO] button.
The device LED will blink number of
times indicating the number of each
digit of the code number. Each digit is
separated by a 1 second pause of the
LED being turned off.
Example :
One blink, three blinks and
eight blinks with an interval of 1 second
of LED being turned off, indicates the
code number 138.
Note :
Ten blinks is equal to the
number 0.
D. Programming a second TV
to VCR Mode.
STEP1
Turn on the TV you wish to
program.
STEP2
Press the [VCR] button to be
programmed and the [SELECT]
button simultaneously for 3
seconds. The [VCR] device
LED will turn on.
*Tip
: The device LED will light on for
20 seconds. The next step must
be entered while the LED is on.
STEP3
Press the [TV] button to
access the TV code table.
STEP4
Point the remote control
toward the equipment and
enter the three-digit code
number assigned to your TV
brand from the code tables.
*Tip
: You can verify that you selected
the correct code by pressing the
[MUTE] button. The equipment
should either turn on or turn off.
STEP5
Store the three-digit code
number by pressing the [VCR]
button once again. The [VCR]
device LED will blink twice to
confirm that the code has
been stored.
E. Programming the
System On/Off Button.
This button is pre-programmed to turn on
all devices with one button press,
however you can also program to turn on
one or two devices by following these
steps:
STEP1
Press the [CBL] button.
STEP2
Press the [SYSTEM ON/OFF]
button and the [SELECT]
button simultaneously for 3
seconds. The [CBL] device
LED will turn on for 20
seconds.
STEP3
Press the [DEVICE] button
you wish to store in the
[SYSTEM ON/OFF] button
and repeat this until you
stored all the power
commands into the
[SYSTEM ON/OFF] button.
STEP4
Press the [CH+] button to save
the power commands you
stored. The [CBL] device LED
will blink twice to confirm the
saving.
F. Program the Volume
Controls.
By following the steps below, you
can program the volume controls
(Volume UP, Volume Down and
MUTE) to your TV, VCR and Audio.
The default volume control settings
on the remote control is TV volume
control. If you wish you can control
the volume via your cable box or
audio equipment. Use the following
steps to change the volume control
settings:
STEP1
Press the [CBL] button and
the [SELECT] button
simultaneously for 3 seconds.
The [CBL] device LED will
turn on.
*Tip
: The device LED will light on for
20 seconds. The next step must
be entered while the LED is on.
STEP2
Press the [ VOL + ] button.
STEP3
Press the [ CBL ], [ AUD ]
(whichever applicable) button.
The [CBL] device LED will
blink twice to confirm the
programming.
To return to original state:
If you wish to restore the TV volume
control in CABLE mode, repeat the
above steps by pressing [ TV ] button in
G. Programming For
Advanced Function.
In the CABLE mode, the [
*
] button can
be programmed to act as a macro or
favorite channel button to send out up
to 10 commands with one button press.
STEP1
Press the [CBL] button to
select the CABLE mode.
STEP2
Press the [
*
] button and
[SELECT] button simultaneously
for 3 seconds. The [CBL] device
LED will turn on for 20 seconds.
STEP3
Press up to 10 buttons you
wish to store. The [CBL] button
LED will blink once for each
command entered.
STEP4
Press the [CH+] button to store
the functions that are selected.
The [CBL] device LED will blink
twice to confirm the storage of
functions.
H. Low Battery Warning.
When the battery is low (2.0V-2.3V) and
needs to be replaced with fresh
batteries, device LED will blink 2 times
in sequence whenever a [DEVICE]
button is pressed to turn on equipment.
I. Memory Lock System.
This remote control is designed to
retain programmed memory for 10
years even after batteries are removed
from the remote control.
J. Write your device Set-up codes.
TV
Set-up Code Number :
VCR
Set-up Code Number :
AUDIO Set-up Code Number :