Remote Control
Extender
INTRODUCTION
The Remote Control Extender is a revolutionary device which will turn virtually any IR (Infrared) remote
control into an RF (Radio Frequency) remote control. No longer do your electronic devices need to be out in
the open for you to control them. Additional benefits of the Remote Control Extender are:
• Send signals through walls and ceilings.
• Control Audio and Video devices which are placed out of sight.
• RF Transmitter is available wherever the remote control is located.
• Installation is as easy as changing a battery
Please ensure that all of the components below are included and follow the 5 Easy installation steps below
and start enjoying the power of RF control.
THIS PACKAGE CONTAINS:
1.
Remote Extender Receiver
2.
IR Blaster Cable (1.5m, 2m and 3.5m in length)
3.
"AAA" RF Transmitter Sleeve
4.
2 Rechargeable 2/3 Size "AAA" Batteries
5.
"AA" Battery Sleeve
STEP 1: INSTALLING THE RF TRANSMITTER AND BATTERY
Simply install the RF transmitter instead of one of the "AAA" or "AA" batteries inside your
remote control.
NOTE:
You may have to change the position of the RF transmitter orientation to have better RF perfor-
mance.
STEP 2: SELECTING THE FREQUENCY
Set the Selection Switch (on the back of the RECEIVER) to:
A : 58KHz (Try this setting if your Scientific Atlanta Explorer or Amino STB is not responding)
B : 38KHz (Default setting and most common setting for IR controlled devices)
C : Sensitivity lower e.g. other equipment using 418 MHz (external
interference). See section: "Interference".
STEP 3: RECEIVER PLACEMENT
Place the RECEIVER next to the corresponding device(s) you wish to control.
STEP 4: CONNECTING THE IR BLASTER CABLE
Connect the IR Blaster Cable into the back of the RECEIVER and place the IR Eye(s) on the receiving
window (IR sensor) of each hidden device you want to control.
TIP:
Shine a flashlight at the front of your device to help find the receiving IR sensor window
NOTE:
There are 3 IR Eyes to control 3 separate devices.
NOTE:
Remove the adhesive tape on the bottom of the IR Eye to secure it on the front of the audio/video
equipment IR sensor.
STEP 5: APPLYING POWER TO THE RECEIVER
Plug the power adaptor in the wall socket and connect the DC connector to the back of the RECEIVER. The
POWER LED on the top of the RECEIVER will illuminate.
YOUR REMOTE CONTROL EXTENDER IS NOW READY FOR USE
RE-CHARGING THE 2/3 SIZE "AAA" BATTERY
The Remote Control Extender's receiver is also used to recharge the 2/3 size battery. The Remote Extender
comes with 2 rechargeable batteries to ensure your RF remote is always ready for use. If your remote control
is functioning at a shorter distance than normal (when the LED (A/B) of the RECEIVER does not blink
when a key on the remote control is being pressed) then the battery needs to be recharged.
1.
Remove the (2/3 "AAA" size) battery from your remote control.
2.
Place the (2/3 "AAA" size) battery in the compartment located on the bottom of the RECEIVER. The
LED (BAT) will light up.
3.
The LED will switch off as soon as the (2/3 "AAA" size) battery is fully charged.
NOTE:
The RF operating range may vary depending on the overall battery charge (e.g. you may have to
replace the "AA"/"AAA" alkaline batteries if the operating range decreases).
CAUTION:
Use only with supplied rechargeable battery. Risk of explosion if battery is installed by an incor-
rect type.
INTERFERENCE
The RECEIVER can be interfered with an external RF signal. The LED (A/B) of the RECEIVER will blink
even without pressing a key on the remote control.
If this is the case, please try the below:
1.
Try to move the RECEIVER (Reminder: The receiver also transmits IR signals, so try placing the
receiver so that it also faces your devices.)
2.
Reduce the antenna length.
SAFETY PRECAUTIONS
• This product should only be used with the CEC approved AC Power supply included in the
packaging.
• Inadequately protected or sensitive electronic equipment may be affected by the use of this product.
• Before you start, please check whether or not this product can affect surrounding equipment.
COMPLIANCE WITH FCC, IC RULES AND REGULATIONS
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and radiates radio frequency
energy and if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try and correct the interference
by one or more of the following measures:
• RE-ORIENT OR RELOCATE THE RECEIVER ANTENNA.
• INCREASE THE SEPARATION BETWEEN THE EQUIPMENT AND THE RECEIVER.
• CONNECT THE EQUIPMENT INTO AN OUTLET THAT IS DIFFERENT FROM THAT TO WHICH
THE RECEIVER IS CONNECTED
• CONSULT THE DEALER OR AN EXPERIENCED RADIO/TELEVISION TECHNICIAN FOR HELP
NOTE:
Changes or modifications not expressly approved by the party responible for compliance could
void the user's authority to operate the equipment.
In compliance with the FCC RF exposure requirements, this device and its antenna must not be co-located
or operating in conjunction with any other antenna or transmitter.
FCC Authorization Label
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1.
THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND
2.
THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE
THAT MAY CAUSE UNDESIRED OPERATION.
FCC ID #: BY4SV1100
ADDITIONAL INFORMATION
This product does not have any user-serviceable parts. Opening the case, except for the battery cover on the
base station, may cause permanent damage to your Remote Extender.
Copyright 2007 by Universal Electronics Inc. No part of this publication may be reproduced, transmitted,
transcribed, stored in any retrieval system, or translated to any language, in any form or by any means,
electronic, mechanical, magnetic, optical, manual, or otherwise, without prior written permission of
Universal Electronics Inc.
For help via the Internet, visit us at:
www.urcsupport.com/extender
For help via e-mail, contact us at:
1
1
2
3
4
4
(x 2)
(x 2)
5
E
Remote Extender 2006.fm Page 1 Wednesday, April 18, 2007 3:23 PM
