background image

 

Unitronics 

 

 

Vision

™PLC+HMI 

Installation Guide 

V130-33-TR34/V130-J-TR34 
V350-35-TR34/V350-J-TR34 
V430-J-TR34 

 

22 Digital Inputs, including 3 HSC/Shaft-encoder Inputs, 
2 Analog inputs 

 

 

8 Relay Outputs

 

 

4 high-speed npn Transistor Outputs

 

V130-33-R34/V130-J-R34 
V350-35-R34/V350-J-R34 
V430-J-R34

 

 

22 Digital Inputs, including 3 HSC/Shaft-encoder Inputs,  
2 Analog Inputs

 

 

12 Relay Outputs 

 

  

General Description 

All of the controllers covered in this guide are micro-PLC+HMIs, rugged programmable logic controllers 
that comprise built-in operating panels and on-board I/Os. 

 

Item 

V130-TR34 

V130J-TR34 

V130-R34 

V130J-R34 

V350-TR34 

V350J-TR34 

V350-R34 

V350J-R34 

V430J-TR34 

V430J-R34 

On-board I/O 

Model Dependent 

Screen 

2.4" 

3.5" Color Touch 

4.3" Color 

Touch 

Keypad 

Yes 

None 

Function Keys 

None 

Yes 

Com Port, Built-in 

 

 

RS232/485 

Yes 

Yes 

Yes* 

Yes* 

Yes* 

USB device, mini-B 

None 

None 

Yes* 

Com Ports, separate 
order, user-installed  

The user may install a CANbus port (V100-17-CAN), and 

one

 of the following: 

 

RS232/RS485 port (V100-17-RS4/V100-17-RS4X)  

 

Ethernet (V100-17-ET2)

 

 

 

Profibus Slave (V100-17-PB1) 

* V430J/V350/V350J comprises both RS232/485 and USB ports; note that only 

one

 channel may be 

used at a time. 

 

Standard Kit Contents 

 

Item 

V130-TR34 

V130J-TR34 

V130-R34 

V130J-R34 

V350-TR34 

V350J-TR34 

V350-R34 

V350J-R34 

V430J-TR34 

V430J-R34 

Controller 

Yes 

Terminal Blocks 

Yes 

Battery (installed) 

Yes 

Slides  
(2 sets of key labels) 

None 

Yes 

None 

Mounting Brackets 

Yes (2 parts) 

Yes (4 parts) 

Rubber Seal 

Yes 

   

   

   

   

   

   

   

   

   

   

   

   

   

   

Summary of Contents for Vision V130-33-R34













Reviews: