background image

 

 

Unitronics 

 

 

Vision

™PLC+HMI 

Installation Guide 

V130-33-TR20/V130-J-TR20 
V350-35-TR20/V350-J-TR20 
V430-J-RH2 

 

12 Digital Inputs, including 2 Analog,  
3 HSC/Shaft-encoder inputs 

 

 

6 Relay Outputs

 

 

2 high-speed npn Transistor Outputs 
(TR20 Only)  

 

General Description 

 

All of the controllers covered in this guide are micro-PLC+HMIs, rugged programmable logic controllers 
that comprise built-in operating panels and on-board I/Os. 

 

Item 

V130-TR20 

V130J-TR20 

V350-TR20 

V350J-TR20 

   V430J-RH2 

On-board I/O 

Model Dependent 

Screen 

2.4" 

3.5" Color Touch 

4.3" Color Touch 

Keypad 

Yes 

None 

Function Keys 

None 

Yes 

Com Port, Built-in 

 

RS232/485 

Yes 

Yes* 

Yes* 

USB device,  

mini-B 

None 

Yes* 

Yes* 

Com Ports, separate 
order, user-installed  

The user may install a CANbus port (V100-17-CAN), and 

one

 of the following: 

 

RS232/RS485 port (V100-17-RS4/V100-17-RS4X)  

 

Ethernet (V100-17-ET2)

 

 

 

Profibus Slave (V100-17-PB1) 

* V430J/ V350 / V350J comprises both RS232/485 and USB ports; 

   note that only 

one

 channel may be used at a time. 

 

Standard Kit Contents 

 

   

   

   

 

 

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

  

Item 

V130-TR20 

V130J-TR20 

V350-TR20 

V350J-TR20 

V430J-RH2 

 

Controller 

Yes 

Terminal Blocks 

Yes 

Battery (installed) 

Yes 

Slides  
(2 sets of key labels) 

None 

Yes 

None 

Mounting Brackets 

Yes (2 parts) 

Yes (4 parts) 

Rubber Seal 

Yes 

Summary of Contents for V130-33-TR20













Reviews: