background image

* All Pictures In This Manual Are For Illustrative Purposes Only. Actual Product May Vary.

© 2023 United States Stove Company, 227 Industrial Park Rd., South Pittsburg, TN 37380      Ph. 800-750-2723

THIS MANUAL IS SUBJECT TO CHANGE WITHOUT NOTICE.

Owner’s Instruction and Operation Manual

Save These Instructions In A Safe Place For Future Reference.

SAFETY NOTICE: If this heater is not properly installed, a house fire may result. For 
your safety, follow the installation instructions. Never use make-shift compromises 
during the installation of this heater. Contact local building or fire officials about 
permits, restrictions and installation requirements in your area. NEVER OPERATE 
THIS PRODUCT WHILE UNATTENDED.

U.S. Environmental Protection Agency

Certified to comply with 2020 particulate 

emissions standards.

 CALIFORNIA PROPOSITION 65 WARNING:

This product can expose you to chemicals including carbon 
monoxide, which is known to the State of California to cause 
cancer, birth defects, and/or other reproductive harm. For 

more information, go to 

www.P65warnings.ca.gov

CAUTION! Please read this entire manual before you install or use your new room 

heater. Failure to follow instructions may result in property damage, bodily injury, or 

even death. Improper Installation Will Void Your Warranty!

WARNING: Before starting your pellet stove remotely with WiFi, it is critical that you 

ensure nothing is leaning, draped or near to your stove. All clearances to combustibles 

specified in your owner’s manual must be maintained at all times.  Failure to comply 

with this warning could result in a fire and or property damage.

US5522-W

R

Report Number: F22-782

Certified to ASTM E1509-2022 and CAN/ULC 
S627:2023; Complies to CAN ICES-3(B)/NMB-

3(B); Contains IC:23243-WBR1DIPEX

Mobile Home / Transportable Building Approved

Model Number:

854002-0606M

Summary of Contents for US5522-W

























































Reviews: