Unitech MS852Plus Auto Switching User Manual Download

Page: 32 / 99

- 17 -

unitech is a registered trademark of unitech Electronics Co., Ltd.

MS852Plus User’s Manual

Chapter 3 – Symbology

3.1 All symbologies

If you want to decode all the symbologies allowable for your scanner, scan the

All Symbologies On code. If on the other hand, you want to decode only a

particular symbology, scan All Symbologies Off followed by the On symbol for

that particular symbology.

Note: Scanner performance may reduce by scanning All Symbologies On.

Only scan All Symbologies On when needed.

When All Symbologies On is scanned, 2D Postal Codes are not enabled.

2D Postal Codes must be enabled separately.

All Symbologies On

All Symbologies Off

3.2 Message Length Description

You are able to set the valid reading length of some of the bar code

symbologies. You may wish to set the same value for mini-mum and maximum

length to force the scanner to read fixed length bar code data. This helps

reduce the chances of a misread.

EXAMPLE

: Decode only those bar codes with a count of 9-20 characters.

Min.length = 09 Max. length = 20

EXAMPLE

: Decode only those bar codes with a count of 15 characters.

Min. length = 15 Max. length = 15

For a value other than the minimum and maximum message length defaults,

scan the bar codes included in the explanation of the symbology, then scan the

digit value of the message length and Save bar codes on the

Programming

Chart

. The minimum and maximum lengths and the defaults are included with

the respective symbologies.

Summary of Contents for MS852Plus Auto Switching


































































































Search results

Summary of Contents for MS852Plus Auto Switching

Reviews:

Related manuals for MS852Plus Auto Switching

Brands by name

Popular brands

Unitech MS852Plus Auto Switching, User Manual

Search results

Summary of Contents for MS852Plus Auto Switching

Reviews:

Related manuals for MS852Plus Auto Switching

Brands by name

Popular brands