Unipulse TM700 Operation Manual Download Page 83 | Manualshive

Page: 83 / 91

background image

74

8

　

SUPPLEMENTS

74

SU

PP

LE

M

EN

TS

Chapter

8

(5) DSP check

Check the backlight and status indicator lamp.
The backlight turns bright by pressing the [Bright] button, and turns
dark by pressing the [Dark] button.
The backlight goes out when the [Light Out] button is pressed, and
after that, it recovers when the screen is touched.
The status indicator lamp lights in green and red alternately.

How to set

(6) PUI check

The pulse input can be confirmed. Press the button of the connector
being currently input. The pulse cycle is displayed.

How to set

(7) COM check

The data displayed under "Transmit data" is sent by pressing the
[Trns.] button.
Under "Receive data", externally transmitted data is displayed.

How to set

Please transmit something information sentence from connected equipment side to the check on the
reception. The data received to "Receive data" is displayed. Please confirm the cable or the setting of
communication condition when it is not correctly displayed, when "Parity" or "Frame" lights in red.
Please press the [Trns.] button to the check on the transmission. The data displayed in "Transmit
data" is transmitted. It will be confirmed to receive it correctly on connected equipment side. Please
confirm the cable or the setting of communication condition when it is not possible to confirm it.

■

Password

This setting is for maintenance and inspection. Do not operate.

SET.

DSP Check

Self Check

→

→

SET.

PUI Check

Self Check

→

→

SET.

COM Check

Self Check

→

→

«
...
81
82
83
84
85
...
»

Summary of Contents for TM700




























































































Reviews:

No comments

Related manuals for TM700

Brand: Gateway Pages: 26

Brand: Parker Pages: 8

Brand: Alienware Pages: 68

Brand: König Pages: 95

NextVision VPW505

Brand: ViewSonic Pages: 2

Brand: Daewoo Pages: 33

COST CONTROL 3362

Brand: La Crosse Technology Pages: 18

Flat Panel LCD Video & Sound Monitor

Brand: Graco Pages: 28

Brand: Anslut Pages: 6

MultiSync FE772

Brand: NEC Pages: 44

Brand: Zenith Pages: 38

Brand: Atari Pages: 22

Brand: Beurer Pages: 4

Brand: Welch Allyn Pages: 28

Brand: Healthy Living Pages: 33

Brand: WattBox Pages: 12

LC-M27-FHD-240-C

Brand: LC-POWER Pages: 63

LTN154X3-L01 - 15.4 WXGA Laptop LCD Screen

Brand: Samsung Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands