Unipulse TM201 Operation Manual Download Page 47

Page: 47 / 58

Function Description Related to Indicated Values

Function Description Relate

d to Indicated Values

Chapter

5-1.

Indicated values

Torque

Analog signals (±5V) from UTM

Ⅱ

are displayed as torque.

Rotation speed

Pulse signals from UTM

Ⅱ

are displayed as rotation speed.

Power

Power calculated from torque and rotation speed are displayed.

Power [W] = 2

X torque [Nm] X rotation speed [rpm] / 60

5-2.

Digital zero

This is a function to set the torque readings to zero.
The digital zero reset function that releases digital zero is also included.

■

Execution procedure

Switch the PC application screen to the
"Waveform" tab.

Click the "Digital Zero/Digital Zero Reset"
button.

This button cannot be clicked in state of standby for the trigger condition or during waveform
acquisition.

Function Description
Related to Indicated Values

Based on these data, torque/power attributes of the rotation speed can be
obtained.

Key points

When digital zero reset is performed, the condition before digital zero correction
is restored.

Key points

Summary of Contents for TM201


























































Search results

Summary of Contents for TM201

Reviews:

Related manuals for TM201

Brands by name

Popular brands

Unipulse TM201, Operation Manual

Search results

Summary of Contents for TM201

Reviews:

Related manuals for TM201

Brands by name

Popular brands