SINGLE
OUTPUT
MONITORED
MODULE
ADDRESSABLE
TYPE
FD 7
20
3OC
INSTRUCTION MANUAL 02-7
203OC
Manufactur
er: UniPOS Ltd. 114 Grenaderska Street, Pleven 5800, R. Bulgaria, http://www.unipos-bg.com
INSTALLATION
Install it according to
fig.
1 in the following sequence:
1.Dismantle the single output monitored module by unscrewing
screws
pos.7 and pos.5.
2.Installation holes and connecting
wire
s holes are drilled on the designated places on the b
ottom
.
3.Fix the
bottom
on the desired place by means of pins and screws. The connecting
wires
are
threaded in advance in the box.
4.Install the
unit carrier
to the
bottom
by
using
screws
pos.5.
5.The electrical connection is done according to
fig.2
. Connect the
wire
s of the signal loop
to the
terminals
pos.1, of the power loop
-
to pos.
3
and the
external devices
-
to pos.2. Connect the negative
leads to “
-
”, the positive
-
to “
+
”, and the shield
s
- to “
Å
”. It is not necessary to take into consideration
the conditional beginnings and ends of the loops. It is recommended cable shoes to be used.
6.Place the cover to the bo
ttom
by using screws pos.7
.
TESTING
The single output monitored module is tested after installation as a part of the site's fire alarm
system or
with
maintenance activities.
The output of the module is tested by the
F
ire
C
ontrol
P
anel. It should be activated and the
respective indication to be on. When the menu is quitted, the single output monitored module should
be
enter
D
uty mode.
SERVICE SCHEDULE
It is done by authorized personnel and includes the following activities:
1.Inspection for visible physical damage
- monthly
2.
T
est
ing
in real conditions
- monthly
WARRANTY
The warrant period is 36 months from the date of
sale
.
The manufacturer guarantees the normal operation of the unit providing that the requirements set
herein have been observed.
The manufacturer does not bear warranty liabilities for damages caused through accidental
mechanical damage, misuse, adaptation or modification after production. The manufacturer bears
warranty liabilities for damages in the unit caused through manufacturer's fault only.
GENERAL DESCRIPTION
The single output monitored module is designed to control external devices for the fire
alarm system
IFS 7000 by means of potential output “Open collector” in case of detecting fire conditions.
The single output monitored module
(fig.1)
consists of
a
printed circuit board (pos.2) and
an
unit
carrier (pos.4), fixed in a plastic box with bottom (pos.1) and a cover (pos.3).The
terminal
s for
connecting the signal loop
SL
(pos.1), the power loop
PL
(pos.
3
), and the external devices
OUT
(pos.2) are located on the printed circuit board
(fig 2)
.
The communication between the
F
ire
C
ontrol
P
anel and the single output monitored module is
completed via the signal loop by the specialized data exchange protocol UniTALK. The single output
monitored module is power supplied by the power loop. Two built-in isolators are provided for short
circuit protection – one on the signal loop and one on the power loop.
Both LED indicators (fig.1, pos.6) provide information for the current status:
- Duty mode
-
red and yellow LEDs flash briefly every 16s;
- Activated output
-
the red LED produces continuous light, the yellow
LED
is not lit;
- Fault condition (activated isolator on the signal loop)
-
the yellow LED flashes briefly every 1s,
the red
LED
is not lit;
- Fault condition (activated isolator on the power loop)
-
the yellow LED flashes briefly every 2s,
the red
LED
is not lit
.
TECHNICAL DATA
S
upply
voltage
:
- signal loop
(15-30)V
DC
- power loop
(12-30)V
D
C
Current consumption in
D
uty mode:
- signal loop
300 µÀ
- power loop
2 mA
C
urrent consumption in
Activated output
:
- signal loop
3 mA
- power loop
up to
200 m
A
Output:
1 pc.
- type
potential, “Open collector”
- voltage
(1
1
-30)V
DC
- maximum current
200 mÀ
C
ross section
of c
onnecting wires
(0,8-2,5) mm
²
Type of the connecting
cables
:
- of the signal loop
two-wire, shielded
- of the power loop
two-wire
- of the
external devices
two-wire
Degree of protection
IP 50
Operational temperature range
minus
10º
Ñ - plus
55º
Ñ
Relative humidity resistance
(93±3)% at
40º
Ñ
Dimensions
120
x
164
x
74
mm
Weight
0,250 kg
1293
051-2
