Unigraf UCD-422 User Manual Download Page 8

Page: 8 / 50

Introduction

Unpacking

The UCD-422 product shipment contains:

•

The UCD-422 unit

•

AC/DC Power supply (100 to 240 Vac 50/60 Hz input, +12 Vdc output)

•

USB 3.0 compliant cable for host PC connection

•

HDMI 2.1 grade HDMI cable

•

Micro-USB type B compatible cable needed for FW programming

•

Ethernet cable needed for FW programming

Installation Package

The UCD-422 software installation package can be obtained from Unigraf download page
at

https://www.unigraf.fi/support/download-links

. Please log in with the following

credentials before attempting to access the download page:
Username:

unigraf

Password:

ruukintie

The installation package is a bundle between the components needed for UCD Console and
for TSI SDK. The bundle contains the following items:

•

Windows drivers (installed during set up)

•

UCD Console software GUI (installed during set up)

•

License Manager (installed during set up)

•

TSI SDK

•

UCD-422 firmware (FW) matching UCD Console version (copied during set up)

•

User Manuals including this document.

When launched, UCD Console verifies that the firmware (FW) version programmed to
UCD-422 matches the launched version. If conflict, UCD Console informs the user. If FW
update is needed please refer to

Firmware Update Procedure

later in this manual for

instructions.

Note:

The software should be installed before connecting the UCD-422 unit in the PC.

Note:

System administrator's privileges are required for performing the installation.

Software Installation



Start the installation by running

Unigraf Software Bundle Setup.exe

Once the installer has started, a welcome page is displayed. The welcome page shows the
software package release version.



Click

Next

to continue. The next two dialogs are used to define the installation folder in

your PC and the Start Menu folder used.



When the selections are ready, click

Install

to start the installation.



Click

Finish

to exit the installation dialog.

Summary of Contents for UCD-422



















































Search results

Summary of Contents for UCD-422

Reviews:

Related manuals for UCD-422

Brands by name

Popular brands

Unigraf UCD-422, User Manual

Search results

Summary of Contents for UCD-422

Reviews:

Related manuals for UCD-422

Brands by name

Popular brands