Unify OpenStage 40 User Manual Download

Page: 54 / 124

Enhanced phone functions

Assigning a station number (not for U.S.)

If this function has been configured (contact your service personnel), you can
selectively assign a specific number (DID number) to your telephone before
making an external call. The assigned number then appears on the called par-
ty’s display.

Open the Program/Service menu



Page 27.

Select and confirm the option shown.



Confirm



Enter the DID number you wish to use.

Dial the external number.

Associated dialing/dialing aid

If this function has been configured (contact your service personnel), you can
use a dialing aid to dial numbers and set up calls for your telephone.



The operating procedure depends on whether the dialing aid is connected to the

bus

or the

a/b (T/R) port.

You can also use your system telephone as a dialing aid for other telephones.

Dialing aid on the S

bus:

On the PC, select a destination and start dialing.

The speaker on your telephone is switched on. Lift the handset when the other
party answers.

Dialing aid at the a/b (T/R) port:

On the PC, select a destination and start dialing.

"Lift the handset" appears on the PC screen.

Lift the handset.

Dialing aid from your telephone for another telephone:

Open the Program/Service menu



Page 27.

Select and confirm the option shown.



Enter the internal station number ("Dial for:").

Enter the number you wish to dial.

Calls

Rufnr. zuweisen

1. ”Differing display view in a HiPath 4000 environment”



Seite 113

Associated dial

Summary of Contents for OpenStage 40





























































































































Search results

Summary of Contents for OpenStage 40

Reviews:

Related manuals for OpenStage 40

Brands by name

Popular brands

Unify OpenStage 40, User Manual

Search results

Summary of Contents for OpenStage 40

Reviews:

Related manuals for OpenStage 40

Brands by name

Popular brands