Unify OpenStage 40 User Manual Download

Page: 32 / 124

Basic functions

Switching to speakerphone mode

Prerequisite:

You are conducting a call via the handset.

Hold down the key and replace the handset. Then release the key.

if nec.

Set the call volume. Keep pressing the key until the desired volume is set.

U.S. mode

If the country setting is set to U.S. (ask the service personnel), you do not have
to hold down the loudspeaker key when replacing the handset to switch to
speakerphone mode.

Press the key shown.

]

Replace the handset. Proceed with your call.

if nec.

Set the call volume. Keep pressing the key until the desired volume is set.

Switching to the handset

Prerequisite:

You are engaged in a call in speakerphone mode.

Lift the handset.

The LED key goes out.

[

Proceed with your call.

Open listening during a call

You can let other people in the room join in on the call. Let the other party know
that you have turned on the speaker.

Prerequisite:

You are conducting a call via the handset.

Activating

Press the key shown. The LED lights up.

Deactivating

Press the key shown. The LED goes out.

Summary of Contents for OpenStage 40





























































































































Search results

Summary of Contents for OpenStage 40

Reviews:

Related manuals for OpenStage 40

Brands by name

Popular brands

Unify OpenStage 40, User Manual

Search results

Summary of Contents for OpenStage 40

Reviews:

Related manuals for OpenStage 40

Brands by name

Popular brands