Unify OpenScape SL6 User Manual Download Page 10

Page: 10 / 93

Setting the display language

Re-opening the battery cover

Charge the battery

Charge the battery fully prior to first use in the charging
cradle or using a standard USB mains adapter.

The battery is fully charged when the power icon

disappears

from the display.

As soon as power is applied to the handset, a Setup wizard starts.

Setting the display language

Press the control key

until the language required is selected on the

display, e.g.

English

press the display key

You can also change the display language later on in the

Settings

menu.

Registering a handset

A handset can be registered to up to four base stations. The registration process depends on the base
station.

Setting the date and time

Set the date/time so that the correct date and time can be assigned to incoming calls and to enable the
alarm to be used.

The active cursor position flashes . . . change cursor position with

. . .

switch between cursor positions with

Enter date:

. . . using

enter the day, month and year in 8-digit format.

Enter time:

. . . using

enter hours and minutes in 4-digit format.

Save settings:

Press the display key

Save

. . . .

Saved

is shown in the display and a confir-

mation tone sounds.

Return to idle status:

Remove the belt clip (if attached).

Place your fingernail in the notch underneath
the battery cover and pull the battery cover
up .

To change the battery, place your
fingernail in the recess in the housing
and pull the battery up

The battery may heat up during charging. This is not dangerous.

After a time, the charge capacity of the battery will decrease for technical reasons.

. . . Use

to select

Settings

Registration

Register

Handset

Select a base (if the handset is already registered with one or more

bases)

Enter the 8-digit registration PIN

Once registration is complete, the handset returns to idle mode.

Press the display key

Time

or, if the date and time have already been set:

. . . use

to select

Settings

OK Date/Time

2,5h

Deutsch

English

Francais

Time

Calls

Date/Time

Date:

15.08.2021

Time:

00:00

Back

Save

Summary of Contents for OpenScape SL6






























































































Search results

Summary of Contents for OpenScape SL6

Reviews:

Related manuals for OpenScape SL6

Brands by name

Popular brands

Unify OpenScape SL6, User Manual

Search results

Summary of Contents for OpenScape SL6

Reviews:

Related manuals for OpenScape SL6

Brands by name

Popular brands