Unify OpenScape Desk Phone IP 55G User Manual Download

Page: 46 / 267

Applications available on your OpenScape Desk Phone IP 55G

Security

Protect your settings and data by assigning a password.

Adjust the settings on your telephone



Page 170

Network information

Information about the IP address of the phone and HTML address of the web interface.

View information on the phone



Page 230.

Diagnostic information

Provides information on all of the important settings of the telephone. Can provide valuable help
in support situations



Page 245.

Reset

Personal settings made via the telephone menu or the web interface can be reset to factory set-
tings



Page 231.

Administration

You can access the administration area via the "Admin" function and by entering the administration
password.

Refer to the administration manual for your phone for more detailed information on this topic.

Applications

E/A Cockpit



Page 139

During a software update, the phone must not be disconnected from the power supply unit,
the LAN line or the phone line.

An update action is indicated by messages on the display and/or by flashing LEDs.

Summary of Contents for OpenScape Desk Phone IP 55G












































































































































































































































































Search results

Summary of Contents for OpenScape Desk Phone IP 55G

Reviews:

Related manuals for OpenScape Desk Phone IP 55G

Brands by name

Popular brands

Unify OpenScape Desk Phone IP 55G, User Manual

Search results

Summary of Contents for OpenScape Desk Phone IP 55G

Reviews:

Related manuals for OpenScape Desk Phone IP 55G

Brands by name

Popular brands