Unify OpenScape Desk Phone IP 55G Page 181 User Manual Download

Page: 181 / 267

Video function

181

Activating and deactivating a function with a key

You can configure a "

Video on

" key to monitor the status of the video function and

respond quickly (see



Page 92). This is useful in the following situations for ex-

ample:
• If the phone is already ringing and you want to quickly activate/deactivate the

video function before answering the call.

• The video status can be identified immediately from the key even if the phone

is in idle mode, the display is switched off or the screensaver is active.

Press the "

Video on

" program key. The key illuminates and the video function is

activated. The video function can be deactivated by pressing the key again.

Summary of Contents for OpenScape Desk Phone IP 55G












































































































































































































































































Search results

Summary of Contents for OpenScape Desk Phone IP 55G

Reviews:

Related manuals for OpenScape Desk Phone IP 55G

Brands by name

Popular brands

Unify OpenScape Desk Phone IP 55G, User Manual

Search results

Summary of Contents for OpenScape Desk Phone IP 55G

Reviews:

Related manuals for OpenScape Desk Phone IP 55G

Brands by name

Popular brands