Unify OpenScape Desk Phone IP 55G User Manual Download | Manualshive

Page: 133 / 267

background image

Making calls with multiple lines

133

Deflecting a call to a DSS station

Prerequisite

: The deflect function is enabled for DSS keys. For information on

the current setting, see

If you receive a call on one of your lines, you can immediately deflect it to the
DSS station.
Your phone rings and a line key flashes.
Press the relevant DSS key. The call is deflected to the DSS station. If the DSS
station does not answer, you can pick up the call by pressing the DSS key.

LED display on DSS keys

DSS Key Meaning

Off

: The line is in idle mode.

Flashes

: You can accept a call for the DSS station via the key. The

call is routed to your primary line when the call is accepted.

Illuminates

: The line is busy. Provided that second call is activated

you can still reach the DSS station via the key. It can accept your
call as a second call.

«
...
131
132
133
134
135
...
»

Summary of Contents for OpenScape Desk Phone IP 55G












































































































































































































































































Reviews:

No comments

Related manuals for OpenScape Desk Phone IP 55G

Brand: NEC Pages: 7

Brand: NEC Pages: 68

Brand: NEC Pages: 44

Brand: Safeline Pages: 32

Brand: UMX Pages: 56

Memoir SGH t929

Brand: Samsung Pages: 196

Brand: Samsung Pages: 23

Brand: Samsung Pages: 7

Brand: Samsung Pages: 2

Brand: Samsung Pages: 50

Brand: Samsung Pages: 37

Brand: Samsung Pages: 95

Brand: Samsung Pages: 131

Brand: Samsung Pages: 153

Brand: Samsung Pages: 155

Brand: Samsung Pages: 189

R225 - SGH Cell Phone

Brand: Samsung Pages: 65

Brand: Samsung Pages: 118

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands