Unify OpenScape Desk Phone IP 55G Page 108 User Manual Download | Manualshive

Page: 108 / 267

background image

108

Enhanced phone functions

Disconnecting the second call

Select the softkey in the second call to confirm. The call to this station is discon-
nected and the call to the first station is reconnected.

Ending the second call by hanging up

If you or the second call partner hangs up, you will be prompted to retrieve the
first call again if "Hold and hang-up" is disabled (

Page 105). Otherwise, the

first call will remain on hold until you receive this prompt after a defined time in-
terval.

Ignoring the second call

Prerequisite:

You are conducting a call and call waiting is allowed

A second call rings.
Select the softkey to confirm

.



The caller still hears the on-hook signal. You can subsequently Accept, Reject
or Deflect the second call for a brief time.

While the ignored second call continues to wait, from the active call you can:
• make a consultation call
• initiate a conference
• toggle between the consultation call and your call partner
• transfer a call

A third call would be rejected with the busy signal. If you have disconnected the
first call, the ignored second call rings like a normal call.

Rejecting a second call

Prerequisite:

You are conducting a call and call waiting is allowed

A second call rings.
Select the softkey to confirm

.

The second call is rejected. The caller hears the busy signal. The caller's phone
number is added to the missed calls list.

Disconnect & return

Ignore

Reject

«
...
106
107
108
109
110
...
»

Summary of Contents for OpenScape Desk Phone IP 55G












































































































































































































































































Reviews:

No comments

Related manuals for OpenScape Desk Phone IP 55G

Brand: Warner Telecom Group Pages: 4

Brand: NEFFOS Pages: 32

Brand: Pantech Pages: 2

Brand: N-Com Pages: 32

Brand: Panasonic Pages: 140

Brand: Panasonic Pages: 32

Brand: Patton electronics Pages: 79

Brand: Micromax Pages: 29

Brand: Profoon Pages: 56

Brand: Slican Pages: 50

Brand: QUO Pages: 28

Brand: Sony Ericsson Pages: 85

Brand: Evolveo Pages: 23

Brand: GAI-Tronics Pages: 92

Brand: Xiaomi Pages: 8

8600 - Cell Phone - CDMA2000 1X

Brand: Audiovox Pages: 74

Brand: Sigma Pages: 52

Brand: U.S.Cellular Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands