Unify OpenScape CP700 User Manual Download Page 162

Page: 162 / 243

162

Line/trunk keys

On a Multi-Line phone the freely programmable keys function as line/trunk keys.

Every key configured as a "line key" (key marking: MULAP X a.k.a Multi-Line Ap-
pearance) corresponds to a line.

As a team member, you yourself can assign the following functions to keys:



page 94:

• Direct station selection (DSS)
• Group call on/off

(not for main phone in the executive/secretary group)

• Ring transfer on/off

(only in executive/secretary group)

Otherwise, you can assign a key with the "MULAP forwarding" (call forwarding)
function for each line.

LED displays for line/trunk keys

Accepting calls on the line/trunk keys

Prerequisite:

Your phone rings and/or the line/trunk key flashes quickly.

Press quickly flashing line/trunk key in the left panel or on a connected Open-
Scape Key Module 600.

Lift the handset.

With handset on hook: Speakerphone mode.

Dialing with line/trunk keys

Press the free line/trunk key in the left panel or on a connected OpenScape Key
Module 600 via which you wish to establish your connection.

Dial phone number.

If the participant answers: Lift the handset.

With handset on hook: Speakerphone mode.

LED

Meaning

Off

– the line is in idle mode.

flashes

Flashing keys are represented by this icon in this manual, without reference to the frequency of

flashes. The flashing interval represents different statuses, which are described in detail in the

corresponding sections of the manual.

– Incoming call on the line
– "Hold reminder" is activated
– the line is on "Hold".

– the line is busy.

MULAP X

Summary of Contents for OpenScape CP700




















































































































































































































































Search results

Summary of Contents for OpenScape CP700

Reviews:

Related manuals for OpenScape CP700

Brands by name

Popular brands

Unify OpenScape CP700, User Manual

Search results

Summary of Contents for OpenScape CP700

Reviews:

Related manuals for OpenScape CP700

Brands by name

Popular brands