manualshive.com logo in svg

Unify OpenScape CP700, User Manual

The Unify OpenScape CP700 Quick Reference Card is a must-have manual for users of this cutting-edge device. It provides clear and concise instructions to maximize its capabilities. Download this helpful guide for free from manualshive.com and harness the full potential of your Unify OpenScape CP700.

Share
Download
background image

117

Deleting advisory messages

@

Press the Main Menu key, if needed.

€

Select "Advisory msg. off".

Confirm.

Assign phone number (not for U.S.)

If configured (ask relevant Administrator), you can assign a specific number (di-
al-up number) to your telephone line before dialing an external number. The as-
signed number then appears on the called party's screen.

@

Press the Main Menu key, if needed.

Open using the Softkey.

Open with the Softkey.

Open with the Softkey.

Confirm.

j

Enter the number you wish to dial.

j

Dial external number.

Rollover

You can set up the volume for all notifications, which occur during your call. For 
more information, see ”Volumes” 

 Page 214.

Advisory msg. off

_

Service/Settings

_

Service Menu

-

_

Calls

-

_

Assign call number

_

Summary of Contents for OpenScape CP700




















































































































































































































































Reviews:

No comments

Related manuals for OpenScape CP700

TCL 30Z Quick Start Manual preview
30Z
Brand: TCL Pages: 22
NEC DT430 Series Quick Reference Card preview
DT430 Series
Brand: NEC Pages: 2
Sagem MYX-4 User Manual preview
MYX-4
Brand: Sagem Pages: 97
Sagem myC5-2 Owner'S Manual preview
myC5-2
Brand: Sagem Pages: 99
Sagem MYC-4 User Manual preview
MYC-4
Brand: Sagem Pages: 99
Sagem myX-6 User Manual preview
myX-6
Brand: Sagem Pages: 89
Sagem MYC-3 Technical Documentation Manual preview
MYC-3
Brand: Sagem Pages: 105
T-Mobile G2x Start Manual preview
G2x
Brand: T-Mobile Pages: 25
TECNO MOBILE LIMITED CD8 User Manual preview
CD8
Brand: TECNO MOBILE LIMITED Pages: 6
Polycom VVX 311 Quick User Manual preview
VVX 311
Brand: Polycom Pages: 2
Pantech C630 User Manual preview
C630
Brand: Pantech Pages: 61
Yezz Andy 3G 3.5 User Manual preview
Andy 3G 3.5
Brand: Yezz Pages: 68
VOICE2NET YL53 User Manual preview
YL53
Brand: VOICE2NET Pages: 2
RugGear RG310 VOYAGER Quick Start Manual preview
RG310 VOYAGER
Brand: RugGear Pages: 31
Samsung SCH-100S Owner'S Manual preview
SCH-100S
Brand: Samsung Pages: 41
Samsung SM-J105B User Manual preview
SM-J105B
Brand: Samsung Pages: 85
Samsung SM-J110L/DS User Manual preview
SM-J110L/DS
Brand: Samsung Pages: 97
Samsung SGH SGH A100 Owner'S Manual preview
SGH SGH A100
Brand: Samsung Pages: 65

Brands by name

Popular brands

Load more brands