Unify OpenScape CP700 User Manual Hfa Download Page 131

Page: 131 / 219

Using Bluetooth

131

Keyboard pairing modes

Keyboard initiates pairing and sets the pairing mode. The pairing mode differs
depending on the keyboard type and manufacturer.

There are three possible pairing modes supported:
• Simple pairing (passkey entry) - if keyboard initiates "simple pairing", PIN is

generated by keyboard and CP700 shows this PIN on display and waits until
the number is typed on the keyboard.

• Legacy (numeric comparison) - if keyboard initiates "legacy" pairing, CP700

generates random number, displays it to user and waits until the number is re-
written on the keyboard.

Just works - if keyboard initiates "just works" pairing, CP700 displays Bluetooth
keyboard pairing request and waits until it is confirmed.

Summary of Contents for OpenScape CP700




























































































































































































































Search results

Summary of Contents for OpenScape CP700

Reviews:

Brands by name

Popular brands

Unify OpenScape CP700, User Manual Hfa

Search results

Summary of Contents for OpenScape CP700

Reviews:

Brands by name

Popular brands