manualshive.com logo in svg

Unify OpenScape 600, User Manual

Share
Download
Unify OpenScape 600 User Manual Download Page 160

160

Switch calls directly to manager

All calls for the manager are usually only acoustically signaled in the admin of-
fice.
You can set the acoustic signaling so that the calls are only acoustically signaled 
on the main phone or on an assigned second phone.

Requirement:

 On your phone there is a key assigned with the "Ring transfer 

executive/secretary" function. 

Activating

Press key. LED lights up.

or

@

If nec. Press Main Menu key.

Open using the Softkey.

Open with softkey.

Open with softkey.

€

Select "Call transfer on". 

Confirm.

Press the required line key.

or

j

Enter the desired line/trunk number.

Deactivating

Press key. LED goes out.

or

@

If nec. Press Main Menu key.

Open using the Softkey.

Open with softkey.

Open with softkey.

€

Select "Call transfer off". 

Ring transfer executive/secretary

-

_

Service/Settings

_

Service menu

-

_

Destinations

-

_

Call transfer on

_

Ln.

-

_

Ring transfer executi-

-

¤

Service/Settings

_

Service menu

-

_

Destinations

-

_

Summary of Contents for OpenScape 600










































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands