manualshive.com logo in svg

Unify OpenScape 600, User Manual

Share
Download
Unify OpenScape 600 User Manual Download Page 158

158

Forwarding calls for lines

You can immediately forward internal and/or external calls to your lines to diffe-
rent internal or external phones (destinations).
If you activate call forwarding for a line, this shall apply to all line keys of your 
group for this line.

@

If nec. Press Main Menu key.

Open using the Softkey.

Open with softkey.

Open with softkey.

€

Select "Frwrdng. MULAP on". 

Confirm.

or

If available, press the key. (You have incompletely saved the "Fwd. MULAP" key 
without type and destination of the forwarding 

 page 84).

Press the required line key.

or

j

Enter and confirm the desired line/trunk number.

Confirm.

or

€

Select "2=only external calls".

Confirm the option shown

or

€

Select "3=only internal calls".

Confirm.

j

Enter the destination number.

Confirm.

or

If available, press the key. (You have also saved the type and destination of the 
forwarding to the "Fwd. MULAP" key, 

 page 84.)

Service/Settings

_

Service menu

-

_

Destinations

-

_

Frwrdng. MULAP on

_

Fwd. MULAP

-

_

Ln.

-

_

1=all calls

_

2=only external calls

_

3=only internal calls

_

save

_

Fwd. MULAP

-

_

Summary of Contents for OpenScape 600










































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands