Unify OpenScape 600 User Manual Download Page 143

Page: 143 / 233

143

Bluetooth settings

Activating and deactivating Bluetooth

You can also configure this setting via the Web interface



page 217.

If nec. Press Main Menu key.

Open using the Softkey.

if nec.

Enter and confirm the User password.

Open using the Softkey.

Activate with the Softkey. The Bluetooth function is activated and is now availa-
ble.

Save the setting by selecting the Softkey.

Changing the Bluetooth name of your OpenScape
CP600

Here you can determine which name your OpenScape CP600 should use to re-
gister at other Bluetooth devices.

You can also configure this setting via the Web interface



page 217.

If nec. Press Main Menu key.

Open using the Softkey.

if nec.

Enter and confirm the User password.

Open using the Softkey

The Bluetooth function was activated for your phone by the administrator.

Service/Settings

User:

Bluetooth

Configuration

Active

¦ _

By factory default, the Bluetooth name is: IntegratedPhone.

If you are currently in the Bluetooth configuration, then the phone is visible.
If you exit the menu, it will be hidden again after a short time.

Service/Settings

User:

Bluetooth

Configuration

Summary of Contents for OpenScape 600










































































































































































































































Search results

Summary of Contents for OpenScape 600

Reviews:

Brands by name

Popular brands

Unify OpenScape 600, User Manual

Search results

Summary of Contents for OpenScape 600

Reviews:

Brands by name

Popular brands