Unify OpenScape 600 User Manual Download Page 115

Page: 115 / 233

115

During the call

Switch to speakerphone

Prerequisite:

You are conducting a call via the handset.

Press and hold the key, hang up handset, and then release the key and continue
the call.

US mode

If the country setting is set to US (ask relevant Administrator ), you do not need
to press the loudspeaker key when you hang up the phone.

Press key.

]

Replace the handset. Proceed with your call.

Switch to handset

Prerequisite:

You are conducting a call via speakerphone mode.

and

[

Lift the handset. Proceed with your call. The hands-free microphone is switched
off.

Open listening in the room during a call

You can allow other people in the room to listen in on the call. Let the other party
know that you have turned on the loudspeaker.

Prerequisite:

You are conducting a call via the handset.

Activating

Press key. LED lights up. The hands-free microphone remains off.

Deactivating

Press key. LED goes out.

Summary of Contents for OpenScape 600










































































































































































































































Search results

Summary of Contents for OpenScape 600

Reviews:

Unify OpenScape 600, User Manual, Page: 115 / 233

Search results

Summary of Contents for OpenScape 600

Reviews: