background image

Troubleshooting

If your

XC800 Series

Cordless Telephone is not performing to your expectations, please try these simple

steps. If you are still unable to resolve the problems, contact Uniden Customer Service at (800) 297-1023,

8:00 a.m. to 5:00 p.m. Central, Monday through Friday.

Problem

Suggestion

Status light won’t come on when handset is placed in base.

Make sure AC adapter is plugged into the base and wall outlet.

Make sure handset is properly seated in base.

Make sure that the charging contacts on the handset and base are clean.

Audio sounds weak and/or scratchy.

Make sure that the base antenna is fully extended and vertical.

Move the handset and/or base to different locations and try again.

Press the

C

button to select another channel.

Can’t make or receive calls.

Check both ends of the base telephone line cord.

Make sure the AC adapter is plugged into the base and wall outlet.

Disconnect the AC adapter for a few minutes, and then reconnect it.

Handset doesn’t ring or receive a page.

Nickel-Cadmium battery pack may be weak. Charge the battery on the base for

15–20 hours.

Extend the base antenna vertically.

The handset may be too far away from the base.

Place the base away from noise sources.

The digital security code may be erased. Set the digital code.

Hear only continuous static from handset and phone will not

turn off.

The power has been interrupted during a call.

Restore power to the base. Make sure the phone is not plugged into an outlet

controlled by a wall switch.

If a power failure has occurred and power will be out for some time, remove

the battery from the handset. This will prevent the battery from completely

discharging.

Specifications

General

The XC800 Series complies with FCC Parts 15 and 68.

Frequency Control

PLL

Modulation

FM

Operating Temperature -10

°

to 50

°

C

Base

Receive Frequency 48.76 to 49.99 MHz

Transmit Frequency 43.72 to 46.97 MHz
Power Requirements 120 VAC 60 Hz

±

3 VAC

Size

7-1/4 in. (H) x 4-3/4 in. (W) x 2-1/2 in. (D)

Weight

Approx. 11.1 oz.

Handset

Receive Frequency 43.72 to 46.97 MHz

Transmit Frequency 48.76 to 49.99 MHz

Power Requirements Rechargeable Ni-Cd Battery Pack

Size

7-1/4 in. (H) x 2-1/4 in. (W) x 2 1/2 in. (D) (w/o antenna)

Weight

Approx. 10 oz. (including battery)

Battery (BT-801)

Capacity

300 mAh, 2.4V

Talk Mode

8 hours

Standby Mode 14 days

Specifications, features, and availability of optional accessories are all subject to change without

prior notice.

11

H:...folded xc800series.vp

Thu Jul 09 15:07:54 1998

Color profile: Disabled

Composite  Default screen

Summary of Contents for XC815













Reviews: