background image

Warranty

10

UHF CB Transceiver

UNIDEN UH405SX-2NB

UNIDEN UH405SX-2NB UHF CB Transceiver

IMPORTANT: Satisfactory evidence of the original purchase is required 

for warranty service

Please refer to our Uniden website for any details or warranty durations offered in 

addition to those contained below.

Warrantor:

 

The warrantor is either Uniden Australia Pty Limited ABN 58 001 865 

498 (“Uniden Aust”) or Uniden New Zealand Limited (“Uniden NZ”) as the case may 

be.

Terms of Warranty: 

Uniden Aust/NZ warrants to the original retail purchaser only 

that the UH405SX-2NB (“the Product”), will be free from defects in materials and 

craftsmanship for the duration of the warranty period, subject to the limitations and 

exclusions set out below.

Warranty period:

 

This warranty to the original retail purchaser is only valid in the 

original country of purchase for a Product first purchased either in Australia or New 

Zealand and will expire one (1) year from the date of the original retail sale.

If a warranty claim is made, this warranty will not apply if the Product is found by 

Uniden to be:  

(A)  Damaged or not maintained in a reasonable manner or as recommended 

    in the relevant Uniden Owner’s Manual;

(B)  Modified, altered or used as part of any conversion kits, subassemblies or 

    any configurations not sold by Uniden Aust or Uniden NZ;

(C)  Improperly installed contrary to instructions contained in the relevant 

    Owner’s Manual

(D)  Repaired by someone other than an authorized Uniden Repair Agent in 

    relation to a defect or malfunction covered by this warranty; or

(E)  Used in conjunction with any equipment, parts or a system not 

    manufactured by Uniden. 

Parts Covered:

 

This warranty covers the Product and included accessories.

User-generated Data: 

This warranty does not cover any claimed loss of or 

damage to user-generated data (including but without limitation phone numbers, 

addresses and images) that may be stored on your Product.

Summary of Contents for UH405SX-2NB













Reviews: